- -
MaxJax Reviews -US
(
http://www.clubcobra.com/forums/australian-cobra-club/110956-maxjax-reviews-us.html)
| sambo |
06-12-2011 05:09 PM |
Looks great Merv. Can you set a maximum lift height?
|
| renovationinnov |
06-12-2011 05:27 PM |
tax refund is now gone on 1 [wife not impressed] on the mates i'll have over to use it to service there cars
overly jelous merv
rob
|
| Merv and Sharon |
06-12-2011 06:24 PM |
Yes Paul there is a stop bar at the top and also a series of points to insert lock bars. I can even use it with the garage door open. No leaks and have just done all the little things like tightening engine mounts, sump gasket, starter terminals, earths, and sprayed up some patches on the exhaust and chassis!
Well done Rob - the small roller stool is great. Get one of those, or on ebay.
|
| LoBelly |
06-13-2011 12:53 AM |
Well done Merv
Routine maintenance will now be so ... routine
I remember Kevin/Funfer2's posts when he was looking at them and thought these hoist were a great solution where headroom is an issue
LoBelly
|
| Merv and Sharon |
06-13-2011 01:47 AM |
Thanks LoBelly. Maybe I should be on commission with Levanta as a few seem to to be buying these ...
Kevin's advice was very influential.
It does make maintenance much easier and the dreaded axle stands can stay in the cupboards.
|
| strida |
06-13-2011 02:55 AM |
You should be on commision Merv, your advise was extremely helpful to me, I've been looking at hoists for a few weeks but height was always the issue.
Almost got a 4 post at one stage but wasn't keen on having jacking trays so that I could remove wheels etc and about $600.00 more plus delivery.
If anybody is looking I believe there are still a couple available on ebay from a queensland site with free delivery australia wide
|
| Merv and Sharon |
06-13-2011 03:06 AM |
Yes Dennis I had the wheels off today to do some cleaning. So easy!
|
| renovationinnov |
06-13-2011 04:16 AM |
hey merv after reading your post about a stool i went into repco & got a roller bed then folds in to a stool or a tool& foot rest low erganomic chair
great to have a customer that owns a franchise store & open on public holidays for short days eheheheheheh
rob can't wait for the hoist now
|
| Merv and Sharon |
06-25-2011 02:00 AM |
Got that hoist Rob?
|
| renovationinnov |
06-25-2011 03:19 AM |
merv department of war & finance said i get it after the tax finish[ july i think
|
| strida |
06-27-2011 04:55 AM |
Merv, received hoist today, Sharon from Levanta threw in a wheelie seat as well.
Easy people to deal with.
|
| Merv and Sharon |
06-27-2011 05:21 AM |
Yes call them up if u have any probs. They offer good advice. Make sure u take all the pack apart before trying to move any of the parts. It is very heavy.
|
| sambo |
06-27-2011 06:56 AM |
Hi Merv, how wide at the widest point when setup for a Cobra? Tax return isn't far away... :D
|
| Merv and Sharon |
06-27-2011 02:34 PM |
Paul mine is 105 inches from widest to widest point. You could do less.
Merv
|
| Mando |
06-27-2011 11:00 PM |
Hi Merv, can you tell me if when the hoist is fully extended in the up position with a car on board can you drive the cobra underneath it and through to the other side?
Regards.
|
| Merv and Sharon |
06-28-2011 12:10 AM |
Never thought of that Mando. Interesting. I am in Melbourne at the moment and cant measure. The Cobra is 1200 high as I recall and the hoist raises it over 4ft. I think it could as the arms would be out of the way. Will have to check that out for you when I get back Thursday. I could have two Cobras?
|
| OZCOBRA |
06-28-2011 12:16 AM |
Quote:
Originally Posted by Merv and Sharon
(Post 1137284)
I am in Melbourne at the moment for you
|
Now I understand where this weather has come from!!!!....What are you doing down here??
You visiting KEW?????....:p |
| Merv and Sharon |
06-28-2011 12:28 AM |
Yeah the Sunshine Coast weather is so boring. Looking for a change Paul. Unfortunately I am stuck at the Crown at a meeting of a government regulatory body (which means nothing will happen) tonite and tomorrow!
|
| strida |
06-29-2011 01:21 AM |
Quote:
Originally Posted by sambo
(Post 1137104)
Hi Merv, how wide at the widest point when setup for a Cobra? Tax return isn't far away... :D
|
Paul,
fyi, I made mine 2800mm inside post to inside post, you could possibly go a little more if required depending on where your chassis rails are and what other vehicles you may want to lift.
My CR main rails are towards the centre, the outer rails are for body mounting only, although the telescopic lift arms would cover most chassis's I beleive.
The included instructions are excellent. |
| Merv and Sharon |
06-29-2011 03:50 AM |
Mine are 2670 from outer post to outer post. I measured both cars involved and that is fine for me. I can use the suspension points just inside the chassis rails.
|
| All times are GMT -7. The time now is 06:17 PM. |
|
Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link:
