- -
Fender spats
(
http://www.clubcobra.com/forums/australian-cobra-club/95606-fender-spats.html)
| 400TT |
03-02-2012 05:31 PM |
Steve, I have used a press stud right at the front/bottom to attach to chassis, you might need a strap to get enough length to reach the chassis.
Then just velcro to inside of the guard to secure the rear edge. Recommend using contact cement etc to adhere velcro to inside the guard as I have found the adhesive on the velcro to not be reliable enough long term.
|
| Merv and Sharon |
03-02-2012 05:47 PM |
That is pretty much it Steve. I have a lift-a-dot (double height post at the top for the tonneau also) and another at the bottom on the inside end of the chassis rail. The spat clips on those and folds under on to a wide (not the narrow stuff) velcro strip (which is glued on as Craig describes). The edge of the spat is sewn where it folds over the edge of the wheel arch, to reduce the pressure on the velcro. We experimented with a sprung steel strip to clip in the spat, inside the wheel arch, but it didn't work out. The leading edge of the spat has stretch elastic sewn in to keep it in place. I have taken them off many times to test them out and all is good.
|
| Steve Gallegos |
01-21-2016 11:58 PM |
Merv and Sharon did you use velcro under the fender to hold the spat on? What about the bottom is there a peg?
|
| Wazza |
01-22-2016 12:34 AM |
That's not bad...
Last post almost 4 years ago....and now a question.
Gotta be a record !!
|
| renovationinnov |
01-22-2016 04:43 AM |
gees i was hoping someone was remaking the stainlees steel ones agian as i was to put in my order for a pair BUT i see not so be to hibation for this thread again
4 years
|
| 07cob |
01-22-2016 02:19 PM |
Quote:
Originally Posted by Wazza
(Post 1378162)
That's not bad...
Last post almost 4 years ago....and now a question.
Gotta be a record !!
|
Warren
I think it is fair enough. Steve actually originally asked the question in March 2012 and has patiently been awaiting an answer.
Quote:
Originally Posted by Steve Gallegos
(Post 1179074)
Merv, how do you attach it to the underside of the wheelwell?
|
Now that is patience!
Steve, Merv doesn't hang around here much although i looks like he last logged on on 31 October last year. Try sending him an eMail - you can do this through his user profile.
Geof |
| All times are GMT -7. The time now is 03:00 PM. |
|
Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link:
