ccx steering column

racco · #1 (**permalink**) 03-21-2010, 07:02 PM

I have found some play in my steering column where the shaft exits the housing. After 25 years of usage the bushing must have worn out. What type of column did the ccx use and is there off the shelf bushings available?

Three Peaks · #2 (**permalink**) 03-21-2010, 07:42 PM

If there isn't, Mickmate should be able to whip one up for you pretty quickly. Just get some measurements - ID of column tube and OD of shaft, length of bushing recess- if there is one.
If the dimensions are pretty simple- IE- 3/4" Outside, 1/2" inside dimension- or something like that, Lowes has a pretty good assortment of Sintered bronze bushings. McMaster carr has a better selection and much better pricing and usually deliver in a couple of days.

Bob

767Jockey · #3 (**permalink**) 03-21-2010, 08:09 PM

Quote:

Originally Posted by racco

I have found some play in my steering column where the shaft exits the housing. After 25 years of usage the bushing must have worn out. What type of column did the ccx use and is there off the shelf bushings available?

Racco,
I had the same problem with my CCX steering column, mine is a MG unit. My problem was the exact same as yours, the bottom bushing was very loose, allowing the shaft to have excess play where it exits the housing. The bottom bushing for this column, believe ot or not, is a simple piece of thick felt that gets oiled or grease impregnated and inserted into the column housing and the shaft passes through it. The top bushing, which I replaced also since I was in there, is a nylon bushing. I got my bushings from a place called Moss Motors, they're on the internet. Google them and you'll be all set to go. Hope this helps.
Doug

65cobraking · #4 (**permalink**) 03-21-2010, 10:25 PM

Made mine out of delron.

767Jockey · #5 (**permalink**) 03-22-2010, 12:05 AM

Nobody likes a showoff, king.....

You're much more talented than I am - I wouldn't know where to start to do that. I guess a chunk of delron (where to buy) and a lathe?

65cobraking · #6 (**permalink**) 03-22-2010, 10:30 AM

Sorry,
Just trying to help.
Your local plastic shop should be able to help you with a piece of delron,and a machine shop will machine you the bushing.

Regards,
Mike.

767Jockey · #7 (**permalink**) 03-22-2010, 11:11 AM

Quote:

Originally Posted by 65cobraking

Sorry,
Just trying to help.
Your local plastic shop should be able to help you with a piece of delron,and a machine shop will machine you the bushing.

Regards,
Mike.

Mike, just pulling your leg on the showoff comment, hence the smiley face...
Outstanding job on the bushing.

Shelboss · #8 (**permalink**) 04-05-2010, 08:20 PM

Contemporary used a custom fabricated steering column.The main shaft is 29.125" long and 1.05" O.D. The steering wheel end necks down to .88", tapers to .8", and is then .72" O.D. and 30 spline, shaft insert is 64-67 MGB. The shaft connecting the column to the rack is 23.5" long, .812" O.D, necked to .75" diameter, and the same 48 spline at the column and rack ends. The U-joints are Borgeson Universals marked with an E7 on each end. The column is 24.75" long and 1.25" O.D. The teflon bushings in the column are about 1.1" ID by 1.125" OD at each end.

mickmate · #9 (**permalink**) 04-05-2010, 09:22 PM

I have seen some scarey looking cobbed together steering shafts on a couple of CCX's. If you need a new splined one piece shaft to replace something like that I use Sweet. Bushings have been pretty well covered but I think I use Delrin. We're making one for Dougs that looks like an original but has the bulge in the side to accomodate the steering shaft like the later CCX's have in glass on theirs.

brett777 · #10 (**permalink**) 08-28-2010, 09:26 PM

hi i bought an ac body loose from frame and no dash or steering column . what should i go with and where can i read on how to install. thank you brett

Danr55 · #11 (**permalink**) 08-29-2010, 05:53 AM

Brett, I have a dash board if you need one. Let me know and I'll post a photo..

mickmate · #12 (**permalink**) 08-29-2010, 10:59 AM

I make those if you have a need. Send me an e-mail address and I'll e-mail you the manuals.

racco · #13 (**permalink**) 08-29-2010, 07:34 PM

I had a look at my column and it had a felt lower bushing and a nylon upper. I ordered a felt bush from the local brit car parts dealer and what a difference it made. The wheel is tight and the play is gone. Only time will tell how long it lasts.

brett777 · #14 (**permalink**) 09-08-2010, 07:08 PM

i bought what i believe was a cmc kit. well done but no steering looks like mustangII steering box. i was told i could go mgb column any thoughts. i want the best i can get for least money. i also need windshield ass and roll bars. if anyone can help. also and lit on attaching body to chassie steps. i have no manuals or steps to follow. thank you brett 252 202 4057

brett777 · #15 (**permalink**) 09-08-2010, 07:13 PM

if anyone can give advice on which way to go installing a steering column i would need cost and steps to install. all i have is steering box with power. thank you brett

mickmate · #16 (**permalink**) 09-08-2010, 07:27 PM

Brett if you can take measurements I can probably help you out with the steering and roll bar.