Commissioning a Turn Key ERA 427 Cobra
Well, the saga began with an interest in a used FFR Mk III, then onto a SPF powered by a 392 Windsor. Then I drove two different ERA 427 Cobras.
The ERA body is beautiful, much more accurate to my eye, and I like the way these cars seem very solid and can be extremely period correct. Being built in the USA is important to me, too. I thought I had snagged a very nice used one. But things were all over the place, and I messed up, and it didn't work out. So now I'm thinking about loosening the purse strings, adding a little to the budget, and having a new one built for me. Here's a summary of the car I'm thinking about: —Wimbledon white, no stripes, standard urethane hardened paint —No roll bar —Under car exhaust —427 Center Oiler (I'm hoping that'll save decent money versus the side oiler) or, if not that, a 428 Cobra Jet. A mild build with iron MR heads, single 4bbl, compression in the nines so I could run it on CA's 91 octane swill. A turkey pan would be cool, with that Stellings air cleaner. Maybe even the pentroof rocker covers. And a somewhat lumpy, but streetable, idle. —Wide ratio Toploader and 3.31 —Few upgrades, primarily the 15" pin drive wheels I'd spec the racing dash with the reverse speedo, but add a glove box. As I said, I'd like the under car exhaust, but prefer the quick jacks instead of the over riders and front hoop/rear bumper. It's turning out, in my head, to be a combo pack of track and street equipage, based purely on my aesthetic preferences. I hope that's not verboten. I'm wondering if anyone has any general suggestions about the process. I'm a sponge when it comes to gathering information and am definitely on the steep part of the learning curve at the moment. Questions at the moment concern ground clearance with the under car exhaust, as well as heat issues, but sounds like it's an extremely well thought out automobile and I'm not overly concerned. Natalie |
Now you're thinking the right way; go for it!
PM sent Cheers, Glen |
I agree ,That is exactly what this is about..:confused: Personalize it for you.:MECOOL:
|
I'd think about some aluminum heads, it would take some weight off the front end and make a little better handling car.
|
Flygirl,
Congratulations on your decision to go with an ERA. Are you building this car to keep it for a long time, maybe 10 years or more? |
Natalie,
Sounds like a great build and you have a good idea of what you are after already. I have two suggestions for the moment: - Contact Peter at ERA and let him know what you have in mind. If you are still interested, put down a deposit to get yourself on the list. - Buy the assembly manual and go over the options list on the ERA website, both are chock full of good information. You will need to be patient ... ERA is wonderful to work with and will build you a beautiful car, but it will most likely take some time. - Tim |
One of the good things about having ERA build the car is that you give your deposit & you have some time to finalize the details. For example, by the time my car was in production I had acquired the funds to purchase the upgrades I really wanted. I called Peter & made the changes. He was happy to do so.
|
Seems like you have made the decision to go ERA ....as the others have said call Peter send in your deposit and depending on if you have a true roller built be prepared to wait. It's a journey not a sprint
|
In response to one of your questions, "heat issues", I put in insulation between the floor and the carpet to keep out some of the heat. I would also suggest (I did this as well) ceramic coating the headers as well as (in what you are talking about) the under car exhaust.
|
Thanks guys.
I admit that I can sometimes be like the girl in Wonka's chocolate factory. The one who said, "but I want it now!" before falling into the vat of bubbling chocolate, never to be seen again. I trust they didn't sell that batch! Anyhow, that's what I'm learning too, about the importance of the journey. Reading the manual a million times and Photoshopping pictures of the car in different configurations, and dreaming about it. I know I'm preaching to the choir. And how cool it'd be to have the car built new, just for me! The reality of it is, I'd be okay with waiting. The long winter is coming and my life is very busy right now, too. Yes, I would be planning to keep it long term. If funds become available, I might have a 427 s/o built sometime in the future and re-power. But other than that the idea would be that it'd be parking in my garage (wherever that may be) for many years to come. This is the car I wish my dad brought could have home in '65, instead of the 427 Galaxie 500 company car (an excellent ride in its own right). I do have some questions about the 427 center oiler. I do know it saw lots of service in boats, but that was a long time ago. Can't quite figure out how expensive an engine this might be, compared to a similarly built 428. I will definitely contact ERA on Monday, and purchase the assembly manual. Years ago I commissioned a 28' sport fishing boat and waited over a year for it to be completed. When it arrived, it was a work of art. The helm area was built for me and fit perfectly, and she was overpowered and went like stink. Just like I hoped. It was very special, and I think this project has the potential to be similar. Natalie |
Hello Natalie,
a friend of mine built a Midstates/Shell Valley cobra with under the car exhaust. If you want me to contact him to get a hold of you, let me know. I had a 428 FE in mine before the side oiler and really liked it. They are cheaper to build also. Getting say, 400 HP/TQ with not much in racing parts and a little machining is not a problem. You should be able to build one for $3,000-$4,000. I would spend more money and get the Cobra Jet heads, as the stock 428 heads need a lot of work. Call someone like Keith Kraft or Barry that are great "FE" engine builders, they have some from stock to wild, at a good price, and will preform very well. Both also have entire motors for sale, and almost crate engines for cobras. The side oilers are expensive to build, but cool to have in a cobra. What do you want out of a engine, mild to wild ? How much can you spend ? If you start out with a 390-428 and build a side oiler later, the motor mounts are the same for both engines. http://i509.photobucket.com/albums/s.../BobsTopon.jpg |
Peter Portante is 50% psychoanalyst and 50% life coach. Spend quality time with
him and reduce your anxiety, save money, eliminate mistakes, and get a great car. |
Peter Portante is 50% psychoanalyst and 50% life coach. Spend quality time with him and reduce your anxiety, save money, eliminate mistakes and get
a great car. . |
What is your budget ?
|
Quote:
|
3-4k for a basic performance 428FE is plenty. I don't know what you're thinking ? If you spend more than that Patrick, where are you putting the money in ?
|
Quote:
|
Natalie,
Stick with Peter and ask him for his candid advice, and you'll do just fine if you have ERA build the car for you. Peter can save you a few $ here and there (engine too) by not getting too caught up in the hype of putting a 427 "side oiler" in a street-use car with a "mild" cam, especially one with no rollbar ;) Those came with 428s (not 427s) originally anyhow if it makes a difference to you. There are some nice "street" version cars with Ford FE 390s and 428s that do just great on the street. At the end of the day, it all looks the same with the same valvecovers and fixtures on top of the motor. IMO: Don't waste the money. A real nice reliable and worthy iron 427 belongs in an original car or on a nice engine stand if you ask me. I'd recommend using the savings on nice leather seats through ERA, maybe some nice pindrive wheels/hubs, getting the body / street flares done right, including all the right fixtures for the engine and compartment, etc. If you plan to drive on trips or longer routes, you might want to consider a 5spd with overdrive vs. a traditional Top Loader 4speed depending on how "purist" you want the car to be and look. Nobody looks under the car anyhow, so maybe a 5speed. Nice paint and body can be costly. However, it can make a car look like a million bucks if its done right. Like I said, Peter can give you the straight scoop if you tell him you just want a nice car and don't want to go over the top, unless that is your objective. I built my car by the way, and watched others order turnkeys. ERA does a great job. Its worth the wait, and be prepared to wait for a turnkey, it takes a while. Have fun. Good Luck. :) PS: There is an ERA Registry poster available now if you want to drool at all the different model ERA cars while you are waiting for yours to be built. |
Quote:
I've heard $15,000-$20,000 for a 427 s/o in mild street trim with nothing fancy; the hope (or should I say fantasy?) is that the center oiler would be significantly less. I think I just like the look of the pentroof valve covers with the 427 cobra logo that's the same as on the fenders of the car. There, I admitted it. I know it's shallow, but there you go. That's why I was considering a center oiler. It's not going to be seeing 10/10ths ever. The whole replica question is interesting to me. Except for the body, there's not that much similar to the original car. And yet, somehow it seems right with the period correct pieces, including the engine. And yes, I know that some street 427s did come with the 428. I suspect that budget constraints will help narrow things down once I learn more. I'm definitely open to guidance, of course from Peter but y'all too. |
450 hp, where did I say that ? Why not just say, 700 ?
Send me a good condition & complete 428, and I'll build it for around that price. It's not hard to do. Anyway, I looked at this a while back. And this is with the non-stock items, almost ready to run, This ad expired 28 days ago. $4,995.00 completely rebuilt ford 428 FE from a '66 police car std bore block from '70 all new parts inside dual 4 bbl intake and windage tray Seller Phone Number: 3173974979 Seller Phone Number2: 3173974979 This item is NEW Trades NOT ACCEPTED Item Location: INDIANAPOLIS http://i509.photobucket.com/albums/s...ord-engine.jpg |
All times are GMT -7. The time now is 09:15 AM. |
Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: