Club Cobra Gas-N Exhaust  

Go Back   Club Cobra > Manufacturers, Engine Builders, tools, and parts. > ERA---Speak with Bob Putnam

Nevada Classics
MMG Superformance
Main Menu
Module Jump:
Nevada Classics
Nevada Classics
MMG Superformance
Keith Craft Racing
Advertise at CC
Banner Ad Rates
MMG Superformance
MMG Superformance
MMG Superformance
March 2024
S M T W T F S
          1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
31            

Kirkham Motorsports

Like Tree2Likes
  • 1 Post By patrickt
  • 1 Post By patrickt

Reply
 
LinkBack Thread Tools Display Modes
  #1 (permalink)  
Old 10-19-2019, 03:24 PM
patrickt's Avatar
Half-Ass Member
Visit my Photo Gallery

 
Join Date: Jun 2005
Cobra Make, Engine: ERA #732, 428FE (447 CID), TKO600, Solid Flat Tappet Cam, Tons of Aluminum
Posts: 21,889
Not Ranked     
Default Breakaway Torque on ERA's Powr-Lok

Just in case anyone was curious as to what the breakaway torque is on a nicely broken in ERA Powr-Lok, I checked mine today on my outboard braked rear. Last year I changed out the fluid (Moroso Climbing Gear Lube) and added one and three quarters bottles of the GM Limited Slip Additive Part #1052358, now #88900330. I added that extra three quarters of a bottle to eliminate a little "ratcheting" that I had been experiencing with the discs sticking around corners and it did the trick nicely. The Powr-Lok specs call for the breakaway torque to be greater than 40 ft/lbs and less than 200 ft/lbs, and it calls for the torque to be what is needed to constantly turn the raised wheel, not to just "break it away." Both of my wheels had the same reading, which was between 60 and 65 ft/lbs. 60 ft/lbs clicked off immediately and did not break the wheel loose, much less turn it, while 65 ft/lbs turned the wheel nicely. Here's a pic, Ellie was helping, but she's off camera.


Gaz64 likes this.
Reply With Quote
  #2 (permalink)  
Old 10-19-2019, 07:35 PM
xb-60's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Aug 2009
Location: Adelaide, SA
Cobra Make, Engine: AP 289FIA 'English' spec.
Posts: 13,139
Not Ranked     
Default

Ellie? That would have to be one of her offspring by now, surely, Patrick?

Oh, and good result with the break away torques.

Cheers,
Glen
Reply With Quote
  #3 (permalink)  
Old 10-22-2019, 11:43 AM
tboneheller's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Jun 2002
Location: Canton, GA.
Cobra Make, Engine: E.R.A. #505
Posts: 216
Not Ranked     
Default

You should be using a beam-style torque wrench to test that if you want accurate numbers.
Reply With Quote
  #4 (permalink)  
Old 10-22-2019, 12:26 PM
patrickt's Avatar
Half-Ass Member
Visit my Photo Gallery

 
Join Date: Jun 2005
Cobra Make, Engine: ERA #732, 428FE (447 CID), TKO600, Solid Flat Tappet Cam, Tons of Aluminum
Posts: 21,889
Not Ranked     
Default

Quote:
Originally Posted by tboneheller View Post
You should be using a beam-style torque wrench to test that if you want accurate numbers.
I probably have four or five torque wrenches, but the only beam one I have is a 1/4" drive for very low torque, like inch pounds when working on a carb. Even after doing this stuff for a good 45 years I simply can not torque something down to less than ten ft/lbs and get it anywhere near right. In fact, I'm more likely to crack whatever it is I'm torquing. Any my "clickable" inch/lb torque wrench doesn't click loudly enough for me to feel or hear it, so it's pretty much useless. But, for this particular project, accuracy wasn't all that important. A range of a couple of ft/lbs is good enough.
cycleguy55 likes this.
Reply With Quote
  #5 (permalink)  
Old 10-22-2019, 02:50 PM
cycleguy55's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Feb 2014
Location: White City, SK
Cobra Make, Engine: West Coast, 460 CID
Posts: 2,844
Not Ranked     
Default

Quote:
Originally Posted by patrickt View Post
I probably have four or five torque wrenches, but the only beam one I have is a 1/4" drive for very low torque, like inch pounds when working on a carb. Even after doing this stuff for a good 45 years I simply can not torque something down to less than ten ft/lbs and get it anywhere near right. In fact, I'm more likely to crack whatever it is I'm torquing. Any my "clickable" inch/lb torque wrench doesn't click loudly enough for me to feel or hear it, so it's pretty much useless. But, for this particular project, accuracy wasn't all that important. A range of a couple of ft/lbs is good enough.
I have 5 torque wrenches, including an old beam torque wrench - that sits in the bottom of a drawer in my tool chest and hasn't been used in about 3 decades.

I had to replace my 1/4" torque wrench because it stopped clicking and I ended up torquing a couple of bolts WAY tighter than they should have been. It's not good when it's an aluminum automatic transmission valve body. Thankfully I stopped before I stripped any of the threads. I still have the old one and have seen instructions online about how to fix it, but I'm not sure it's worth the time and energy.
__________________
Brian
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 08:39 AM.


Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: CC Policy
Links monetized by VigLink