Keith Craft Inc.- We service what we sell!!! Check out our Cobra engines!!! We build high performance racing engines and components for the fast pace strip racing industry as well as daily drivers who want to be FIRST!!!

FE Forums sponsored by Keith Craft Inc.


Go Back   Club Cobra > Engine Building, Tuning, and Induction > FE TALK

Welcome to Club Cobra!  The World's largest non biased Shelby Cobra related site!

  •  » Representation from nearly all Cobra/Daytona/GT40 manufacturers
  •  » Help from all over the world for your questions
  •  » Build logs for you and all members
  •  » Blogs
  •  » Image Gallery
  •  » Many thousands of members and nearly 1 million posts! 

YES! I want to register an account for free right now!  p.s.: For registered members this ad will NOT show

MMG Superformance
Nevada Classics
MMG Superformance
Main Menu
Nevada Classics
Nevada Classics
MMG Superformance
Advertise at CC
Banner Ad Rates
MMG Superformance
MMG Superformance
MMG Superformance
November 2025
S M T W T F S
            1
2 3 4 5 6 7 8
9 10 11 12 13 14 15
16 17 18 19 20 21 22
23 24 25 26 27 28 29
30            

Kirkham Motorsports

Reply
 
LinkBack Thread Tools Rate Thread Display Modes
  #1 (permalink)  
Old 09-21-2009, 04:40 PM
CC Member
Visit my Photo Gallery

 
Join Date: Aug 2008
Location: Yorba Linda, CA
Cobra Make, Engine: Legendary Autos, 427 SC
Posts: 62
Not Ranked     
Default

67FEFASTBACK If you are thinking of Webers I have a set upp for you. I removed from my Cobra because the guy I bought the car from didn't put on a 10 degree cut manifold but put a straight on (which would fit a 67GT) and cut a hole in the hood. I removed to repair the hood and scope for the Cobra and installed a Holly setup. A couple of things I have noticed. I lost bottom end torque, response is a bit off due to new vac sec, and most of all everybody tells me it diesn't sound the same. Sounds better with Webers!.
The manifold I have is a Harmon Moody, and Webers were powder coated Red. I have all the linkage fuel lines to the regulator, New 40 mm chokes, (not installed yet) New F14 emulson tubes and a spare set of main jets and idle jets, and two diffrent sets of KN filters (Tall & Short). I was going to change chokes as suggested in this forum but rrealized that I travel so much I really do not have time to plasy I just want to drive. As Iit turns out I do miss the Webers and was going to keep but now I will sell to partly finance new side pipes. The other BIG thing is the WOW FACTOR. Everybody crowds around a car with Webers!!!!!! call me at 714 401-6054 or PM me. Look in the for sale adds under my name I have pics in the add. I will get you into webers for a third of the cost!
Reply With Quote
  #2 (permalink)  
Old 09-21-2009, 09:17 PM
67FEfastback's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Sep 2008
Cobra Make, Engine:
Posts: 109
Not Ranked     
Default

Quote:
Originally Posted by OCCOBRA View Post
67FEFASTBACK If you are thinking of Webers I have a set upp for you. I removed from my Cobra because the guy I bought the car from didn't put on a 10 degree cut manifold but put a straight on (which would fit a 67GT) and cut a hole in the hood. I removed to repair the hood and scope for the Cobra and installed a Holly setup. A couple of things I have noticed. I lost bottom end torque, response is a bit off due to new vac sec, and most of all everybody tells me it diesn't sound the same. Sounds better with Webers!.
The manifold I have is a Harmon Moody, and Webers were powder coated Red. I have all the linkage fuel lines to the regulator, New 40 mm chokes, (not installed yet) New F14 emulson tubes and a spare set of main jets and idle jets, and two diffrent sets of KN filters (Tall & Short). I was going to change chokes as suggested in this forum but rrealized that I travel so much I really do not have time to plasy I just want to drive. As Iit turns out I do miss the Webers and was going to keep but now I will sell to partly finance new side pipes. The other BIG thing is the WOW FACTOR. Everybody crowds around a car with Webers!!!!!! call me at 714 401-6054 or PM me. Look in the for sale adds under my name I have pics in the add. I will get you into webers for a third of the cost!
Thanks kindly for the link, and information. Too bad my car or engine bay is not red, otherwise it would be a great way to go!
__________________
http://youtu.be/1x63nB64zyM
Thunder
Reply With Quote
Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 10:59 PM.


Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: CC Policy