Club Cobra Gas - N Exhaust  

Go Back   Club Cobra > Engine Building, Tuning, and Induction > Fuel Injection & Tuning

Nevada Classics
Main Menu
Module Jump:
Nevada Classics
Nevada Classics
Advertise at CC
Banner Ad Rates
Keith Craft Racing
MMG Superformance
March 2024
S M T W T F S
          1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
31            
  #1 (permalink)  
Old 12-12-2010, 07:12 PM
CC Member
Visit my Photo Gallery

 
Join Date: Mar 2004
Cobra Make, Engine:
Posts: 12
Not Ranked     
Default Jeg's AN Push-Loc fittings?

Question:

Do these work pretty well if you get the hose that they recommend for them?

http://www.jegs.com/i/JEGS/555/105061/10002/-1

They say 250 psi. I've never used anything without a standard type of hose clamp before.
Reply With Quote
  #2 (permalink)  
Old 12-13-2010, 03:17 AM
CC Member
Visit my Photo Gallery

 
Join Date: Mar 2001
Location: E BRUNSWICK N.J. USA,
Posts: 3,841
Not Ranked     
Default That's only the couple rating

roger1 Roger that clamp still needs neither a crimp clamp or a screw clamp to keep the hose on the end. This also ONLY work with rubber inner hose. You can use them with Plastic hose BUT have seen it split. Doesn't work with SS line. If you call and ask Jeg's, they can tell you which hose to use. I double clamp all rubber hoses to motor and radiator ends. Rotate them 180 degrees apart. this makes for a strong connection and prevents leaks or lines popping off under pressure if a clamp loosen over time. Rick L.
Reply With Quote
  #3 (permalink)  
Old 12-13-2010, 03:18 AM
CC Member
Visit my Photo Gallery

 
Join Date: Dec 2001
Location: Louisville, KY
Cobra Make, Engine: I'm Cobra-less!
Posts: 9,389
Send a message via AIM to blykins
Not Ranked     
Default

Yes, they work pretty well. I've used the Aeroquip version for fuel lines.
__________________
www.lykinsmotorsports.com
Reply With Quote
  #4 (permalink)  
Old 12-13-2010, 05:23 AM
Rwillia4's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Aug 2003
Location: San Diego, CA
Cobra Make, Engine: BDR #455, KC427W, TWM-FI
Posts: 727
Not Ranked     
Default

They are a pain to get on! getting the hose on the nipple is easy, getting the outer part all the way down sucked. Maybe I was doing it wrong... I just remember "don't buy those again" was my experience.
Reply With Quote
  #5 (permalink)  
Old 12-13-2010, 06:30 AM
CC Member
Visit my Photo Gallery

 
Join Date: Mar 2004
Cobra Make, Engine:
Posts: 12
Not Ranked     
Default

Thanks for the replies.

I am going to give them a try.
I also ordered a 10ft piece of the hose they say must be used with them.
Reply With Quote
  #6 (permalink)  
Old 12-13-2010, 09:33 AM
CC Member
Visit my Photo Gallery

 
Join Date: Mar 2001
Location: Madison, AL, al
Cobra Make, Engine: Midstates in-work again
Posts: 73
Not Ranked     
Default Press on fittings

I used these on my EFI fuel lines with no problems, they work great. However I bought the Ford blue hoses and it takes a while to get use it them, not seeing the SS braided lines.
__________________
Treblig
Reply With Quote
  #7 (permalink)  
Old 12-16-2010, 10:14 AM
CC Member
Visit my Photo Gallery

 
Join Date: Mar 2004
Cobra Make, Engine:
Posts: 12
Not Ranked     
Default

Got them yesterday.
So far, I like them. They were very easy to install and their recommended hose turned out to be Gates which wasn't stated. I didn't use heat but just a little WD40 and they went on without that much effort. It will be a while till I fire this engine so I won't know about how they hold till then but, I'm not expecting any problems.

Gates LOL Hose



Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 03:43 PM.


Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: CC Policy
Links monetized by VigLink