 
Main Menu
|
|
Nevada Classics
|
|
Advertise at CC
|
| S |
M |
T |
W |
T |
F |
S |
| |
1 |
2 |
3 |
4 |
5 |
6 |
| 7 |
8 |
9 |
10 |
11 |
12 |
13 |
| 14 |
15 |
16 |
17 |
18 |
19 |
20 |
| 21 |
22 |
23 |
24 |
25 |
26 |
27 |
| 28 |
29 |
30 |
|
|
|
|
|
|
CC Advertisers
|
|
04-16-2004, 01:37 PM
|
|
CC Member
|
|
|
Join Date: Mar 2004
Location: Wallingford,
CT
Cobra Make, Engine:
Posts: 22
|
|
Not Ranked
How to Install 48 IDF WEBER Carburetors onto a Tunnel Ram Manifold: Step 1
Photo #1 shows a Wieand tunnel ram intake manifold, which has been machined to accept the spacing of 48 IDF WEBER carburetors. Once the manifold has been cut and machined, flat dimensions must be held to eliminate warpage.
__________________
Jessica Wysocki, Advertising & Marketing
Inglese Induction Systems
400 S.Orchard St.
Wallingford, Ct 06492-2512
203-265-3617
www.inglese.com
Last edited by Jessica Wysocki; 04-16-2004 at 02:28 PM..
|
04-16-2004, 01:39 PM
|
|
CC Member
|
|
|
Join Date: Mar 2004
Location: Wallingford,
CT
Cobra Make, Engine:
Posts: 22
|
|
Not Ranked
Step 2
Photo #2 shows a reinforcing plate, which has been welded to the manifold. A closer look will show you that the 8 threaded holes have been installed for the mounting of a ½ inch thick mounting plate.
__________________
Jessica Wysocki, Advertising & Marketing
Inglese Induction Systems
400 S.Orchard St.
Wallingford, Ct 06492-2512
203-265-3617
www.inglese.com
|
04-16-2004, 01:41 PM
|
|
CC Member
|
|
|
Join Date: Mar 2004
Location: Wallingford,
CT
Cobra Make, Engine:
Posts: 22
|
|
Not Ranked
Step 3
Photo #3 shows the machined mounting plate installed into the machined manifold. You can see that the 8 mounting holes used countersunk screws for holding the plate onto the intake manifold. You can also see that we have machined clearances for the accelerator pump adjusting screws.
__________________
Jessica Wysocki, Advertising & Marketing
Inglese Induction Systems
400 S.Orchard St.
Wallingford, Ct 06492-2512
203-265-3617
www.inglese.com
Last edited by Jessica Wysocki; 04-16-2004 at 01:48 PM..
|
04-16-2004, 01:44 PM
|
|
CC Member
|
|
|
Join Date: Mar 2004
Location: Wallingford,
CT
Cobra Make, Engine:
Posts: 22
|
|
Not Ranked
Setp 4
Photo #4 is the completed assembled system. You can see how neatly it has been constructed. Using the short 1 ½ inch tall stacks, it will clear the hood scoop of any Cobra. The linkage is actuated by a center bellcrank and operates very smoothly.
Inglese Induction Systems can build this and many other types of systems for you! Contact Dan Miller at 203-265-3617 or e-mail him at iisystems@aol.com
Visit www.inglese.com for more information
__________________
Jessica Wysocki, Advertising & Marketing
Inglese Induction Systems
400 S.Orchard St.
Wallingford, Ct 06492-2512
203-265-3617
www.inglese.com
|
04-16-2004, 02:05 PM
|
|
CC Member
|
|
|
Join Date: May 2003
Location: Newburgh, IN,
IN
Cobra Make, Engine: 427SC Unique
Posts: 481
|
|
Not Ranked
I do have a question for you. I notice there are heat dispensing spacers under the carbs. Do you sell them? How thick are they? How much are they?
Thanks
Brent
|
04-16-2004, 02:08 PM
|
|
CC Member
|
|
|
Join Date: Mar 2004
Location: Wallingford,
CT
Cobra Make, Engine:
Posts: 22
|
|
Not Ranked
Yes we sell them; they are Phenolic spacers.
3/8 inch thick
$110.00 each set
8 come in a set
Call To Order: 203-265-3617
__________________
Jessica Wysocki, Advertising & Marketing
Inglese Induction Systems
400 S.Orchard St.
Wallingford, Ct 06492-2512
203-265-3617
www.inglese.com
Last edited by Jessica Wysocki; 04-30-2004 at 08:19 AM..
|
03-20-2009, 05:56 PM
|
|
CC Member
|
|
|
Join Date: Nov 2004
Location: Bettendorf,
IA
Cobra Make, Engine:
Posts: 33
|
|
Not Ranked
Couple more Qs
Nice looking result. So the top plate is just mechanically fastened with gasket or sealant? Correct?
How do these modified TRam intakes actually perform? Are there any unusal reversion induced problems associated with mismatch between the cross section of the runner and carb opening at the interface with top plate?
Thanks,
Kelly
Last edited by kcoffield; 03-20-2009 at 06:05 PM..
|
03-20-2009, 07:07 PM
|
 |
CC Member
|
|
|
Join Date: Feb 2007
Location: Colorado Springs,
CO
Cobra Make, Engine: Backdraft, supercharged Coyote
Posts: 2,433
|
|
Not Ranked
You realize, of course, that this thread is 5 years old. Inglese is now owned by Comp Cams. And I havn't seen anything like this in their catalog.
|
03-21-2009, 05:26 AM
|
|
CC Member
|
|
|
Join Date: Nov 2004
Location: Bettendorf,
IA
Cobra Make, Engine:
Posts: 33
|
|
Not Ranked
New about comp's purchase but didn't look at date. -Thanks.
|
06-10-2015, 04:56 PM
|
|
CC Member
|
|
|
Join Date: Jun 2015
Cobra Make, Engine:
Posts: 6
|
|
Not Ranked
looks good!
__________________
1984 AUTOKRAFT COBRA #009
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -7. The time now is 05:33 PM.
Links monetized by VigLink
|
Linear Mode
