|
Quote:
I haven't gotten an email from you Tim :confused: David :):):) |
Quote:
Whoops ... sent the email to ... parts at kirkhammotorsports dot com Just sent again to the gmail account mentioned earlier in the thread ... sorry about that! :p - Tim |
billet 427 SOHC valve covers
David, can you post a picture of the 427 SOHC billet valve covers?
|
Guys,
The next parts I am going to post pictures of are no longer for sale. They sold today before I could even get them online.. However, I figured you all would like to see what we have been digging up. These are the exhaust manifolds for an AC 427 Cobra street car. They are extremely rare. Notice the exhaust manifolds are NOT symmetrical. The right manifold is on top. The left manifold is on bottom. http://www.clubcobra.com/photopost/d...88_Medium_.JPG Notice the heat riser port on the left manifold to run the choke on the dual quad carbs. http://www.clubcobra.com/photopost/d...89_Medium_.JPG Casting numbers for the left manifold. http://www.clubcobra.com/photopost/d...90_Medium_.JPG Other side of the left manifold. http://www.clubcobra.com/photopost/d...91_Medium_.JPG Right manifold. I have no idea why the casting numbers are the same. http://www.clubcobra.com/photopost/d...92_Medium_.JPG Right manifold http://www.clubcobra.com/photopost/d...93_Medium_.JPG Right manifold and left manifold together. Right is on top. http://www.clubcobra.com/photopost/d...94_Medium_.JPG Right manifold and left manifold together. Right is on top. http://www.clubcobra.com/photopost/d...95_Medium_.JPG |
These are 9 bin organizers. The tilt out drawers are about 2 inches x 2 inches.
I think we paid $10 each for them in a big quantity buy. I'll let these go for $5 each. We probably have 20 of them. New, in the wrapper. http://www.clubcobra.com/photopost/d...97_Medium_.JPG As you can see in the below photo, we use them to organize lots of nuts and bolts and little parts. These bins (and the parts inside them aren't part of the sale :LOL: ) http://www.clubcobra.com/photopost/d...98_Medium_.JPG |
We have 5 of these Nisonger reproduction Smiths Tachs. They retail at $100 each??? Not sure, someone correct me if I'm wrong. I'll let these go for $50 each. New, in the box.
4 SOLD http://www.clubcobra.com/photopost/d...00_Medium_.JPG http://www.clubcobra.com/photopost/d...01_Medium_.JPG |
I found a box of the original type sway bar mounts. They are made from aluminum.
We have: 1 set of 1" 3 sets of 7/8" 1 set of 3/4" (The size we normally use for our front sway bars). 1 side only of 1/2" 1 side only of 13/16" 1 side only "not drilled" These for $75/set. I'll let the sets go for $15. I'll let the ones that only have 1 side go for $5 each. http://www.clubcobra.com/photopost/d...02_Medium_.JPG |
These came off a 289 Comp car. Now, that doesn't mean they are "original." Those cars had a hard life and exhaust was expendable. The Snap Lock (Nice product Jorgen) floor tiles are 1 foot squares.
These are used and abused. Dented and scratched. $50 owns them. Shipping will be $50. SOLD http://www.clubcobra.com/photopost/d...04_Medium_.JPG |
Hey David
any chance you have a Canton oil pan....15-680S - 351W FRONT SUMP I know its a long shot but I had to ask.:LOL: |
SOLD
This is a Mark Williams MAGNESIUM housing for a Ford 9 inch. This was part of our project when we went to Snezhinsk, Russia to work with nuclear weapons engineers on a nuclear non-proliferation project. I think we paid $500 for the case. Let me know if someone finds a link. Make a reasonable offer. Brand new. http://www.clubcobra.com/photopost/d...03_Medium_.JPG |
|
Quote:
Not sure. I have an entire container left to go through. I'll look. David :):):) |
Quote:
The valve covers start out as a $360 billet of aluminum (I just asked Sandwich). They take 15 hours to machine each. :eek: http://www.clubcobra.com/photopost/d...05_Medium_.JPG http://www.clubcobra.com/photopost/d...06_Medium_.JPG http://www.clubcobra.com/photopost/d...07_Medium_.JPG http://www.clubcobra.com/photopost/d...08_Medium_.JPG |
I am reposting this as the thread is getting quite long. I just took pictures of the seat covers AND reduced the price.
SOLD I found the old seat covers to CSX3104. They are NOT the original seat covers. They were probably done 25 years ago. The leather on them is still good, but used, of course. I'll take a picture of them in the morning. I'd let them go for $250 :eek: PRICE REDUCED $175 http://www.clubcobra.com/photopost/d...09_Medium_.JPG http://www.clubcobra.com/photopost/d...10_Medium_.JPG David :):):) |
Quote:
Larry |
Radiator 22" x 19"
Upper 1 1/2" Lower 1 3/4" Brand new. $100 SOLD http://www.clubcobra.com/photopost/d...19_Medium_.JPG |
50 feet of exhaust thermal wrap. $25 New, in the box.
SOLD http://www.clubcobra.com/photopost/d...18_Medium_.JPG |
Plastic fuel cell custom made for a 289 FIA car. The fuel cell was probably made by roto-molding. Never had fuel in it. Retail $2000. Today $900
Inside foam will need to be replaced. http://www.clubcobra.com/photopost/d...16_Medium_.JPG http://www.clubcobra.com/photopost/d...17_Medium_.JPG |
Turkey pan. This is our expensive, one piece turkey pan. Just like original. Retail $400. Today $200. We have 5 of these. We found a few more.
8 SOLD http://www.clubcobra.com/photopost/d...15_Medium_.JPG |
Time to go home for Krossfit. I'll post something really special tomorrow. :D
You won't want to miss it. I'll post it around 11:00 am MST. David :):):) |
| All times are GMT -7. The time now is 04:07 PM. |
Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: