|
Quote:
David :):):) |
Quote:
David :):):) |
Quote:
David :):):) |
Aluminum front jack hooks. Powder coated black. The powder coating is bad and they will need to be repainted.
$50 both $40 http://www.clubcobra.com/photopost/d...21_Medium_.JPG |
It seems like this thread isn't going away any time soon :LOL:
David :):):) |
Differential 2
Differential with axle housings and bearings. This differential case had the OUTER pinion bore machined over sized. If you want to bore it out and sleeve it you can save a very expensive case. The differential unit is a 19 Power Lock--the same unit used in an original car. The axle housings are copies of the original with the taper roller bearings. You will have to clean or replace the bearings. Differential case $2000 Side axle housing with bearings $300 x 2 for $600 Power Lock Differential $475 Retail $3075 Today $900 $800 http://www.clubcobra.com/photopost/d...03_Medium_.JPG http://www.clubcobra.com/photopost/d...04_Medium_.JPG |
Front rotors. Used. Blue from heavy braking. Lightly grooved.
12.2 x 1.25 $25 pair $20 http://www.clubcobra.com/photopost/d...93_Medium_.JPG |
Rotor 12.2 x 1.25
Has a casting flaw. Garage Art $20 $15 http://www.clubcobra.com/photopost/d...94_Medium_.JPG http://www.clubcobra.com/photopost/d...95_Medium_.JPG |
Quote:
David :):):) |
Quote:
|
If you happen to have Water Temp and Oil Press gauges still around I'd be interested in those as well.
|
Right rear jack hook that had a bad day.
Steel Garage Art $15 $10 http://www.clubcobra.com/photopost/d...22_Medium_.JPG |
Quote:
The recital was beautiful. I should post a YouTube :) David :):):) |
Quote:
David :):):) |
Quote:
Prototype carburetor feed lines. The ends are dash 8. One of the hexes is machined slightly off as well. Retail $50 Today $20 $10 for both http://www.clubcobra.com/photopost/d...66_Medium_.JPG |
THESE CAME BACK UP FOR SALE. THE CUSTOMER DECIDED TO BUY OUR STAINLESS PIPES INSTEAD.
These are pictures of prototype 427 S/C head tubes. These head tubes are not completely welded and will need some tweaking and welding to finish them up. Tubes are made from mild steel. Retail $1,000. Today $250. $200 Please see the below description. Below: Left head tubes. Notice the "hole" between head tube #5 and #6. That is where the steering shaft goes through the pipes on the original car. The #5 tube is to the right in the below photo. http://www.clubcobra.com/photopost/d...37_Medium_.JPG The #5 tube is to the left in the below photo. http://www.clubcobra.com/photopost/d...38_Medium_.JPG #7 and #8 are do not have the flanges welded to the tube. They are only tacked into place. http://www.clubcobra.com/photopost/d...40_Medium_.JPG #7 only has the tube tacked together. It is not welded together. http://www.clubcobra.com/photopost/d...41_Medium_.JPG The flange on #7 is 3/16-1/4" of an inch away from the flange. The tube will have to be stretched and tweaked to fit. http://www.clubcobra.com/photopost/d...42_Medium_.JPG The following 2 pictures are of the right side. The right side head tubes are quite short--just like an original car. http://www.clubcobra.com/photopost/d...43_Medium_.JPG http://www.clubcobra.com/photopost/d...44_Medium_.JPG |
Below are a set of 427 head tubes that fit a 351 motor.
Notice the head tubes extend all the way out of the body. We designed these so the merge collector on the side pipe is outside the body--just like CSX3020 that Dave Dralle used to drive. These are made from steel. The flanges will bolt onto the narrow exhaust bolt pattern. They are brand new and in perfect condition. Head tubes retail $1000. Today $500 $400 http://www.clubcobra.com/photopost/d...46_Medium_.JPG |
FE motor mounts
Picture of the different kinds below: After Market mounts. We have two sets of these mounts. Please note, one of the studs is longer than the other one. That won't matter when you put in your motor, but just making sure you know. We have 4 each. 3 with the short stud. 1 with the long stud. $10 each $5 each http://www.clubcobra.com/photopost/d...48_Medium_.JPG WE ALSO HAVE 4 FORD MOUNTS LEFT Ford C6SZ mounts. We used these mounts for years on our cars until they were no longer available. Retail $75 each Today $35 each. $30 each http://www.clubcobra.com/photopost/d...49_Medium_.JPG http://www.clubcobra.com/photopost/d...50_Medium_.JPG |
427 dash panel. The one in the picture has been powder coated black. We don't have any more powder coated dashes. We will extend this sale to our normal, unpainted aluminum dashes until we sell the rest of these parts.
$350 Retail. UNTIL SALE ENDS $150 http://www.clubcobra.com/photopost/d...71_Medium_.JPG |
We have 2 trunk trays for a 427 street car. They are very similar to the trunk tray of a 289 car and can be used in a 289 car. (The 289 car has a cross molded into the bottom.) This one has the holes already drilled in it for access to the differential bolts. This one already has the roll bar holes in both sides.
Retail $450 Today $125 $100 http://www.clubcobra.com/photopost/d...78_Medium_.JPG |
| All times are GMT -7. The time now is 06:16 PM. |
Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: