Need engine installer for a Kirkham
 

I'm looking for a new engine installer that can also install a top and heater for my Kirkham project. The current installer has postpomed my project that was scheduled to begin in early March because something more imortant and bigger has come up.

I need to find someone with lots of experience in top installation that can also install the engine and heater on a Kirkham.

I don't care where they are located, I just need top quality work.

Can anyone help?

Have used these guys a number of times.


http://www.roaring60.com/roaring60/

You will be welcome at our workshop. Lets ship your car !!!!!!

Cobra work
 

I just had an engine built/installed by these guys. They did a superior job.
www.palmettorestorations.com

Rob Camp at Keith Craft Motorsports in Plano, Texas. Plano is a northern suburb of Dallas (Texas). Rob has done a bunch of Kirkham's, Shelby's, Superformance etc. Contact Rob at 972-578-3550 or see link on clubcobra.

He is the best!!!!!!

Call Tom Bernard at Tom's Motorsports. He is located down the street from Shelby's on Speedway Blvd. Suite X-112 at the Las Vegas Motor Speedway complex, 702-651-0708 and he is a Shelby authorized shop. He not only can install your engine and transmission but he can build them for you. And he can set up your chassis after the engine is installed.
Your Kirkham, if like mine will come pretty close, these cars are infanitly adjustable since there are Rod Ends on every A-arm and link on the car. Just like a race car. Your everyday wheel alignment shop will not be able to do this. Corner weights, ride height etc.. Plus his location makes it easy for quick high speed road testing. I opted to change springs from the springs delivered on the car. He worked on my car for 2 day's until I was happy with how it drove. These cars are hand full, especially if they don't work right.
I have a Southern Automotive sideoiler in my car. I wanted my car painted and Southern recomended Jodeco Auto down the road from them In McDoungh Ga. I had my car shipped down there and had Bruce Paint and install the engine and trans. and the interior. He did a good job although the alignment was not something he could tackle, so I had Tom do that.
Either one of these shops will do a good job for you. I live in Washington State and had Rich's Transport bring the car from Georgia to Tom's in Vegas where I met him with my rig. Rich told me that "your car is absolutly stunning" before he unloaded it, and he's seen alot of Cobras. So if your considering painting your car Jodeco is very good and reasonable.

DO NOT USE KEITH CRAFT MOTORSPORTS OF PLANO TEXAS!!!!!!!!!!!!!!!! Keith Craft of Texarkana may be acceptible although they were not supportive of addressing the deficiecies of KC Plano. KC of Plano did my BDR and it was not acceptalbe. PM for details.

Rob ~ you have mail.

skydash, that is my 67 mustang under "completed projects" done by Palmetto Restorations. They do great work. chuck

My main concern is getting someone with experience in installing tops in the aluminum bodies that can also install the drivetrain with top quality work. Do the above named folks do tops? I have emailed some of them. Thanks for the help.

I forgot,

Forget the Heater you won't need it. When these cars warm up they warm up. The heat transfers thru the body like an Aluminum Frying Pan even in the cool climate of the Pacific Northwest where I live. Not to mention the heat from the side pipes. Remove the Polished Stainless heat shields of the foot wells and put some Kevlar mat between the fiberglass foot box and the Stainless. Also put reflective Kevlar material inside of all the aluminum pieces that make up the transmission tunnel or you'll regret it.
Before you install the engine! Stop and go traffic is why you need it the most.

If your car has a Roll Bar, Forget the top, it won't fit the car. I had Jodeco do a Toneau cover with all the post snaps installed in the body. The Cover is made with flaps that velcro around the roll bar. The Toneau's and tops and all are copies of the originals and can be purchased at Finishline and Cobra Restorers just to mention a few.

I would strongly suggest calling Cobra Restorers. Chuck has assembled a lot of Kirkhams and it would be hard pressed to find someone else with his experience. He knows the parts and the resources to make it all come together. He may not be the most personable as some say, but his experience with original and Kirkhams is far better than most I've seen. Give Kirkham a call and ask his advice. I don't know where your located but it would be worth the trip!! They have my car right now and they are basically getting it to the point that I can take over. 770-427-0020 Thanks, Matt.

If you are in the mid-Atlantic region, call Steve Hague of Polarstar Engineering. He has done great things with my car and with others. His website is www.polarstarengineering.net. His phone number is 302-368-4639. Talk with Steve and you will immediately understand that he is well qualified and very reasonable.

risomes, help us out and let us know where you live,a name would be nice also. It is hard to help if you do not give us info.

Chuck-
Sent you a pm on "the other site" :)

My name is Rob. I am 45 minutes west of Philadelphia, PA. But as long as the shop is in the continental USA, it doesn't matter where it is located.

I am looking for a shop that:

1) Has a lot of experience installing tops on Kirkham and Shelby Cobras with a rollbar.
2) Does top quality work in drivetrain installation
3) Can install heaters.

I think the only complication on my list is the top. However, I have gotten some leads and names from you guys that I have followed up with.

I think I am okay now. Thank you for your help.

If location is not an issue, Mike McCluskey.

kirkham might do it

Mike is the one that I was working with that has postponed my project . . .