Club Cobra Gas-N Exhaust  

Go Back   Club Cobra > Manufacturers, Engine Builders, tools, and parts. > RU Car Crafters--Speak with Roger Upton

MMG Superformance
Nevada Classics
MMG Superformance
Main Menu
Module Jump:
Nevada Classics
Nevada Classics
Keith Craft Racing
MMG Superformance
Advertise at CC
Banner Ad Rates
MMG Superformance
MMG Superformance
Keith Craft Racing
MMG Superformance
March 2024
S M T W T F S
          1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
31            
  #1 (permalink)  
Old 09-05-2002, 07:55 PM
Ibr8k4vetts's Avatar
Senior Club Cobra Member
Visit my Photo Gallery

 
Join Date: Jan 2001
Location: Santa Barbara, Ca., ca
Cobra Make, Engine: R.U.C.C. with a 427FE, toploader
Posts: 1,435
Not Ranked     
Default RUCC brakes?

Dose anyone know what calipers Roger uses on his kit? I got my kit on 7/28/02 and just got done with pluming the brake....suprise one rear caliper dose not work and the front caliper leaks
Thanks Mike
Reply With Quote
  #2 (permalink)  
Old 09-05-2002, 08:19 PM
dlowe01's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Nov 2001
Location: Broken Arrow, Ok
Cobra Make, Engine: RU Carcrafters / 408 Stroker
Posts: 100
Not Ranked     
Default

Let Roger know and he will take care of it for you. Some times a little slow but he will.
Reply With Quote
  #3 (permalink)  
Old 09-05-2002, 08:27 PM
Ibr8k4vetts's Avatar
Senior Club Cobra Member
Visit my Photo Gallery

 
Join Date: Jan 2001
Location: Santa Barbara, Ca., ca
Cobra Make, Engine: R.U.C.C. with a 427FE, toploader
Posts: 1,435
Not Ranked     
Default

I've tried to get a hold of him, the last time I herd from him he said he was sending my missing parts on Friday that was three weeks ago. I think it will be much faster to buy some new ones. I wish I had the manual for the car.
Mike
Reply With Quote
  #4 (permalink)  
Old 09-05-2002, 08:37 PM
dlowe01's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Nov 2001
Location: Broken Arrow, Ok
Cobra Make, Engine: RU Carcrafters / 408 Stroker
Posts: 100
Not Ranked     
Default

Did you go with the 11" roters with the adapters for the front? What rear end?
Reply With Quote
  #5 (permalink)  
Old 09-05-2002, 08:41 PM
Ibr8k4vetts's Avatar
Senior Club Cobra Member
Visit my Photo Gallery

 
Join Date: Jan 2001
Location: Santa Barbara, Ca., ca
Cobra Make, Engine: R.U.C.C. with a 427FE, toploader
Posts: 1,435
Not Ranked     
Default

yes, the rear end is a 9"
Thanks, Mike
Reply With Quote
  #6 (permalink)  
Old 09-05-2002, 08:49 PM
dlowe01's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Nov 2001
Location: Broken Arrow, Ok
Cobra Make, Engine: RU Carcrafters / 408 Stroker
Posts: 100
Not Ranked     
Default

The front calipers are going to be a GM product, I think I have the info. on them in the Garage and will get it for you tomorrow. I used a 8.8 rear end so am not sure on the rear. I will try to find that out also if possible. I am about done with my car so if you need any help or info. just let me know and I will help you out any way I can. Look for info. tomorrow. Also I have some of the manual, if you would like I could scan if for you and e-mail it to you. Just let me know.
Reply With Quote
  #7 (permalink)  
Old 09-16-2002, 08:18 PM
Leo Leo is offline
CC Member
Visit my Photo Gallery

 
Join Date: May 1999
Location: Denton, TX,
Posts: 50
Not Ranked     
Default

I took notes during a phone conversation with Roger. My notes say that the front 11" brake rotors are from a '78' Granada, bearings from a 74-78 Mustang II with a V8 and the calipers and pads are metric, from a GM, probably an early '80's Monte Carlo of Cutlass. I hope this helps!!
Reply With Quote
  #8 (permalink)  
Old 09-17-2002, 08:42 AM
CC Member
Visit my Photo Gallery

 
Join Date: Sep 1999
Location: Sand Springs, OK
Cobra Make, Engine: RUCC
Posts: 15
Not Ranked     
Default

Mike

If you will send your calipers back I can get my suppliers to warranty them.
The front calipers are GM Metric. The rear are off of a Cadalic El Dorado.
I have sent your other parts if you do not have them please call or email me and let me know.

Roger Upton
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 02:11 AM.


Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: CC Policy
Links monetized by VigLink