Club Cobra Keith Craft Motorsports  

Go Back   Club Cobra > Manufacturers, Engine Builders, tools, and parts. > Superformance

MMG Superformance
Nevada Classics
Keith Craft Racing
Main Menu
Module Jump:
Nevada Classics
Nevada Classics
MMG Superformance
MMG Superformance
Advertise at CC
Banner Ad Rates
MMG Superformance
Keith Craft Racing
March 2024
S M T W T F S
          1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
31            
  #1 (permalink)  
Old 05-13-2018, 09:11 AM
CC Member
Visit my Photo Gallery

 
Join Date: May 2015
Posts: 618
Not Ranked     
Default Rear cockpit bulkhead oilcanning

So I've tracked down a rattle to the fire extingisher mounted to the back of the cockpit CL on the rear bulkhead, which is appears to me an unreinforced single Matt of fiberglass...it is separate from the front bulkhead in the trunk: the gap is visible from the sie of the car above the rear wheels.

Thinking about simply fabbing up a piece of wood to fit relatively tight in there transversely, slathering with sikaflex, and screwing the extinguisher mount to it from the front, and a temporary screw from the trunk to secure it while setting up?

Any one else tackled this issue?

Thanks

Steve H
1764

Last edited by tortuga; 05-13-2018 at 09:17 AM.. Reason: Revised for clarity
Reply With Quote
  #2 (permalink)  
Old 05-17-2018, 08:30 AM
Apex_speed's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: May 2018
Location: Denver, CO
Cobra Make, Engine: Superformance Mk3 with Roush 427R
Posts: 77
Not Ranked     
Default

I observed the same thing on my car (#2312) which was interesting as the Hillbank guys had told me they thought there was only one layer with no void.

I think your solution would work BUT I would get a spacer in there and then through bolt through BOTH bulkheads from the trunk with machine screws and then use some nice cap nuts on the cockpit side.

There might be some better ideas coming as I haven't actually done that yet but it's on the list to put the extinguisher there or on the tranny tunnel under the dash.
Reply With Quote
  #3 (permalink)  
Old 05-19-2018, 04:28 AM
CC Member
Visit my Photo Gallery

 
Join Date: Feb 2003
Location: Jonesboro GA,
Posts: 382
Not Ranked     
Default

I'm not familiar with this particular car, but very familiar with composites. How big is the void in both square inches and gap, how many bolts?

Depending on void size, I'm thinking along the lines of injecting an epoxy solid filler into the bolt holes to make an approximately 1" solid pad to redrill and through bolt. You could also do the same in any areas where flex is an issue. Not talking large areas, just injecting in strategic areas to stop the movement.
Reply With Quote
  #4 (permalink)  
Old 05-19-2018, 11:59 AM
Buzz's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Feb 2000
Location: St. Lucia, West Indies, WI
Cobra Make, Engine: Unique 427SC 383 stroker
Posts: 3,725
Not Ranked     
Default

The epoxy is a good idea. I was going to suggest injecting expanding foam depending on depth of the void.
__________________
Tropical Buzz

Grant me the serenity to accept the things I cannot change, the strength to change the things I can, and the wisdom to know the difference. -(wasn't me)

BEWARE OF THE DOGma!! Dogmatism bites...
Reply With Quote
  #5 (permalink)  
Old 05-19-2018, 05:51 PM
Blas's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Sep 2002
Cobra Make, Engine: SPF#0760
Posts: 3,387
Not Ranked     
Default

Perhaps a piece of hi density foam pushed between the two surfaces will do the trick?
Blas
__________________
Wiring Diagrams: SPF MKII, MKIII, GT40, CSX7000, CSX8000, Corvette Grand Sport, and Shelby Sebring, Bondurant & Cinema Tribute Cars.
Owner’s Manuals: SPF MKII, CSX7000, CSX8000, Sebring, Bondurant, & Cinema Tribute Cars.

Large, easy to read and trace schematics with part numbers, wire colors, wire gauge, fuses, and electrical upgrade information. Trouble-shooting and replacement part numbers for those roadside repair adventures.
SPFWiringDiagrams@Comcast.net
Reply With Quote
  #6 (permalink)  
Old 06-25-2018, 08:43 PM
CC Member
Visit my Photo Gallery

 
Join Date: May 2015
Posts: 618
Not Ranked     
Default

If you remove the rear wheels from a SPF you can look right though a void about 1.5" wide probably a good foot high? I think some stiff foam cut very precisely to the right thickness and very parallel could be slipped in there and bonded some how. Expanding foam would work with the right volume and mold...might be hard to control and possibly make a big mess...
Reply With Quote
  #7 (permalink)  
Old 06-25-2018, 08:59 PM
Apex_speed's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: May 2018
Location: Denver, CO
Cobra Make, Engine: Superformance Mk3 with Roush 427R
Posts: 77
Not Ranked     
Default

Just an update as I put my car on my lift and looked back there yesterday. When it's up in the air, you can reach two hands up over the differential and get in there to back it up with a metal plate. I'm using a 1/8" aluminum plate through bolted from the inside. In other words, there is a MILE OF ROOM in there but you have to get under the car. I would not want to go in from the side after looking at it carefully. That would still be a pain.
Reply With Quote
Reply

Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 11:19 PM.


Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: CC Policy
Links monetized by VigLink