Main Menu
|
Nevada Classics
|
Advertise at CC
|
S |
M |
T |
W |
T |
F |
S |
|
1 |
2 |
3 |
4 |
5 |
6 |
7 |
8 |
9 |
10 |
11 |
12 |
13 |
14 |
15 |
16 |
17 |
18 |
19 |
20 |
21 |
22 |
23 |
24 |
25 |
26 |
27 |
28 |
29 |
30 |
|
|
|
|
|
CC Advertisers
|
|
08-08-2021, 02:02 PM
|
|
Senior Club Cobra Member
|
|
|
Join Date: Jul 2000
Location: Chilliwack,BC,
BC
Cobra Make, Engine: F5 Roadster
Posts: 1,415
|
|
Not Ranked
Does bellhousing hang below round tube frame?
F5 mark 4 cobra, does the bellhousing sit above or below the 4" round frame, trying to figure out ground clearance.
thanks,
Perry
__________________
F5 cobra Mark 4 roadster, Ruby Wine Red with pearl,
dual 2" roll bars, warmed up 302, E Street aluminum Heads, Comp cam and roller rockers, AOD, 4.10 Eaton Possi, Power Baer/disc brakes, block hugger headers, 2 1/2" under car exhaust, F500 18" black spoke wheels.
|
08-08-2021, 02:18 PM
|
|
CC Member
|
|
|
Join Date: Jan 2018
Location: Lafayette,
IN
Cobra Make, Engine: Looking to buy
Posts: 1,295
|
|
Not Ranked
Although lots run with their oil pans down below the frame I would not. I'd get the most compact pan available and go from there.
__________________
Cobra loving, autocrossing Grandpa Architect.
|
08-08-2021, 08:54 PM
|
|
Senior Club Cobra Member
|
|
|
Join Date: May 2001
Location: Florence,
AL
Cobra Make, Engine: RCR GT 40 & 1966 Fairlane 390 5 speed
Posts: 4,511
|
|
Not Ranked
I ran a road racing pan. Stock height with 8 qts capacity.
__________________
''Life's tough.....it's even tougher if you're stupid.'' ~ John Wayne
"Happiness Is A Belt-Fed Weapon"
life's goal should be; "to be smarter than inanimate objects"
|
08-09-2021, 03:28 AM
|
|
CC Member
|
|
|
Join Date: Aug 2013
Location: Canandaigua,
NY
Cobra Make, Engine: SPF MKII Riverside Racer FIA
Posts: 2,473
|
|
Not Ranked
He's asking about the bell housing on an FFR. I can't answer that question for you, as I have an SPF and mine is the 289 model with the 3" tubes.
__________________
|
08-09-2021, 06:53 AM
|
CC Member
|
|
|
Join Date: Sep 2002
Location: Grand Rapids,
MI
Cobra Make, Engine: FFR Challenge Car, RDI aluminum 427w
Posts: 347
|
|
Not Ranked
Generally, yes. Many builders on the FFR forums mention this. Seems to hold with 302/351 and Coyotes. The recommendation is often to cut the bottom of the bellhousing to match the bottom of the 4" frame rails. There are also many warnings about having an oil pan sit below the frame rails.
Having had two SPF cars I was accustomed to the front sway bar being the low point under the frame at the front and used that as a guide for what hung down. In 65,000 miles never hit the bellhousing or oil pan. This was with a 3-1/2" or so height to both and driving cross country, city, country and dirt roads. YMMV
The standard recommendation for chassis height on the FFR at the bottom of the 4" frame tubes is 4" at the front and 4-1/2" in the rear. This is an approximate and often varied from. The SPF chassis used similar heights.
I understand the concern but wonder if this merits the effort.
Jim
|
08-09-2021, 07:00 AM
|
CC Member
|
|
|
Join Date: Sep 2018
Location: Jacksonville,
FL
Cobra Make, Engine: B&B-McGill
Posts: 57
|
|
Not Ranked
Found this photo. Not sure if it will help.
|
08-09-2021, 08:15 AM
|
|
Senior Club Cobra Member
|
|
|
Join Date: Jul 2000
Location: Chilliwack,BC,
BC
Cobra Make, Engine: F5 Roadster
Posts: 1,415
|
|
Not Ranked
need a stock bellhousing measurement
I need a stock 302/ T5 bellhousing measurement- above or below frame- for F5 mark 4 as a reference point for my AOD and it's trans pan height. On my 1st shell valley cobra my C6 pan was low and banged speed bumps
__________________
F5 cobra Mark 4 roadster, Ruby Wine Red with pearl,
dual 2" roll bars, warmed up 302, E Street aluminum Heads, Comp cam and roller rockers, AOD, 4.10 Eaton Possi, Power Baer/disc brakes, block hugger headers, 2 1/2" under car exhaust, F500 18" black spoke wheels.
|
08-09-2021, 01:06 PM
|
CC Member
|
|
|
Join Date: Dec 2015
Posts: 1,442
|
|
Neutral
|
08-10-2021, 03:19 AM
|
|
CC Member
|
|
|
Join Date: Jan 2018
Location: Lafayette,
IN
Cobra Make, Engine: Looking to buy
Posts: 1,295
|
|
Not Ranked
Quote:
Originally Posted by Jim Vander Wal
Generally, yes. Many builders on the FFR forums mention this. Seems to hold with 302/351 and Coyotes. The recommendation is often to cut the bottom of the bellhousing to match the bottom of the 4" frame rails. There are also many warnings about having an oil pan sit below the frame rails.
Having had two SPF cars I was accustomed to the front sway bar being the low point under the frame at the front and used that as a guide for what hung down. In 65,000 miles never hit the bellhousing or oil pan. This was with a 3-1/2" or so height to both and driving cross country, city, country and dirt roads. YMMV
The standard recommendation for chassis height on the FFR at the bottom of the 4" frame tubes is 4" at the front and 4-1/2" in the rear. This is an approximate and often varied from. The SPF chassis used similar heights.
I understand the concern but wonder if this merits the effort.
Jim
|
Cutting off the bell housing will leave the flywheel exposed, won't it?
__________________
Cobra loving, autocrossing Grandpa Architect.
|
08-10-2021, 05:21 AM
|
CC Member
|
|
|
Join Date: Sep 2018
Location: Jacksonville,
FL
Cobra Make, Engine: B&B-McGill
Posts: 57
|
|
Not Ranked
Quote:
Originally Posted by t walgamuth
Cutting off the bell housing will leave the flywheel exposed, won't it?
|
If you follow the FF forum link that was provided by spdbrake apparently one guy did it with success.
|
08-10-2021, 05:56 AM
|
CC Member
|
|
|
Join Date: Sep 2002
Location: Grand Rapids,
MI
Cobra Make, Engine: FFR Challenge Car, RDI aluminum 427w
Posts: 347
|
|
Not Ranked
You only cut part of the lower flange. Maybe 3/8-3/4".
No, you don't cut into the flywheel area.
Jim
|
08-10-2021, 08:55 PM
|
|
CC Member
|
|
|
Join Date: Jan 2018
Location: Lafayette,
IN
Cobra Make, Engine: Looking to buy
Posts: 1,295
|
|
Not Ranked
I see. That is a lot less than I imagined. Of course that lip around the bell housing flange is like the web on a steel beam so any cutting on it will weaken it some.
__________________
Cobra loving, autocrossing Grandpa Architect.
|
08-11-2021, 07:16 AM
|
|
CC Member
|
|
|
Join Date: Apr 2009
Location: Little Rock area,
AR
Cobra Make, Engine: ERA Street Roadster #782 with 459 cu in FE KC engine, toploader, 3.31
Posts: 4,483
|
|
Not Ranked
Not all aftermarket bell housings are the same. In general QuickTime are a bit more compact than Lakewood. Also QuickTime makes a non-SFI rated, steel bellhousing with a block saver plate that is quite a bit less bulky, especially along the bottom part where it does away with the heavy, wide flange and continuous row of large bolts - for a narrower flange with just a few small machine screws. If you going to the strip or someplace you need an SFI rated bellhousing this is the way to go with a Cobra. Good ground clearance, heavy steel bell with the weakened zone oriented down, block saver plate, usually dials in good on factory dowels.
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -7. The time now is 01:58 PM.
Links monetized by VigLink
|