Club Cobra GasN Exhaust  

Go Back   Club Cobra > Manufacturers, Engine Builders, tools, and parts. > Antique & Collectibles

MMG Superformance
Nevada Classics
Keith Craft Racing
Main Menu
Module Jump:
Nevada Classics
Nevada Classics
MMG Superformance
Advertise at CC
Banner Ad Rates
MMG Superformance
MMG Superformance
MMG Superformance
March 2024
S M T W T F S
          1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
31            

Kirkham Motorsports

Like Tree1Likes
  • 1 Post By Speedwaypj

Reply
 
LinkBack Thread Tools Rate Thread Display Modes
  #1 (permalink)  
Old 09-16-2016, 09:40 AM
CC Member
Visit my Photo Gallery

 
Join Date: Sep 2007
Location: Sanford, FL
Cobra Make, Engine: A&C (near future)-460
Posts: 99
Not Ranked     
Smile Ordered Body - Royal Blue

Yesterday, I finally Ordered my Body - Royal Blue - Ultra luster Gel coat - Tan leather interior.
Sonny said 6 - 8 weeks....no problem since I bought my 429/460 45 years ago. Started frame build 5 years ago....Fired motor this last Fathers day.
.......I was always going to do Red, but I guess I got tired of thinking about Red after 45 years.
Also, I was going to order my drive shaft but Denny suggested waiting until I mount the body incase I need to move rear axle Fwd or Aft. Has anyone had an issue with having to adjust the rear axle after mounting the body?
Looking forward to this next part of the build. I do plan to upload some pics of my build to date.
I've always appreciated responses on this site!
PJ
bjretired likes this.
Reply With Quote
  #2 (permalink)  
Old 09-23-2016, 06:56 AM
PNJSNAK's Avatar
Club Cobra Member
Visit my Photo Gallery

 
Join Date: Nov 2000
Location: Macedonia, OH
Cobra Make, Engine: A&C 427S/C, 351W, T5
Posts: 513
Not Ranked     
Default

PJ
For me, Pete Clark made sure everything on my rolling chassis was square.
I mounted the motor /tranny then measured and ordered my driveshaft from Denny's.
Mounted the driveshaft and then picked up the body.
Once I had the body I positioned it on chassis to what looked the best to me, tire fit in the wheel wells front to back and square all around.
Once I was satisfied I put 4 drilled holes thru the body interior area and frame and used the large pop rivets as dowel position pins.
This way I could take the body on and off as needed before I was ready to bolt it down for good.
Don't forget to put the felt material on the top of the frame rails before you first put the body on the chassis.
I did this 15 years ago and shortly after A&C had done minor changes to the molds, but no changes to the basic body shape. I believe it was to the wheel flares, hood and doors.
The only adjusting I ever did to the rear end was adjusting the angle of the pumpkin using the adjustable 4 link tie rods.
You will need 4 people to lift the body.
Good luck, take your time.
__________________
OhioCobraClub.com
Reply With Quote
  #3 (permalink)  
Old 09-27-2016, 06:58 PM
CC Member
Visit my Photo Gallery

 
Join Date: Sep 2007
Location: Sanford, FL
Cobra Make, Engine: A&C (near future)-460
Posts: 99
Not Ranked     
Default

Thanks! Great suggestions! What about clearence between lower bell housing to ground? Mine looks low. thx
PJ
Reply With Quote
  #4 (permalink)  
Old 09-28-2016, 06:31 AM
PNJSNAK's Avatar
Club Cobra Member
Visit my Photo Gallery

 
Join Date: Nov 2000
Location: Macedonia, OH
Cobra Make, Engine: A&C 427S/C, 351W, T5
Posts: 513
Not Ranked     
Default

PJ
Not very much,same with oil pan.
Just under 4".
You have to watch curbs and stuff on the road.
I can remember years ago I came across a raised area in the road and tried to straddle it and the next thing I know my oil pressure was dropping and temps rising.
Stopped and looked back to an oil trail.
The drain plug was gone.
The threads were good and I just replaced it, I think it simply was unthreaded by the edge
of the road surface.
__________________
OhioCobraClub.com
Reply With Quote
Reply

Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 04:37 PM.


Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: CC Policy
Links monetized by VigLink