Main Menu
|
Nevada Classics
|
Advertise at CC
|
S |
M |
T |
W |
T |
F |
S |
|
1 |
2 |
3 |
4 |
5 |
6 |
7 |
8 |
9 |
10 |
11 |
12 |
13 |
14 |
15 |
16 |
17 |
18 |
19 |
20 |
21 |
22 |
23 |
24 |
25 |
26 |
27 |
28 |
29 |
30 |
|
|
|
|
|
CC Advertisers
|
|
10-05-2013, 03:20 PM
|
|
CC Member
|
|
|
Join Date: Mar 2003
Location: Wickenburg AZ- PHX, Cinci, Indy before,
AZ
Cobra Make, Engine: FFR Mk 3 408 530 - 585 T- mustang Dyno at B&R
Posts: 1,836
|
|
Not Ranked
Wiper blades
My rubber is shot. Like I used it once last year. Where other than cut to the chase and get it from Finish Line? O'Reily has the bracket but not the 10 inch blade. Suggestions ?
|
10-05-2013, 03:24 PM
|
|
CC Member
|
|
|
Join Date: Jun 2001
Location: Mesa,
AZ
Cobra Make, Engine: ERA #2119 289FIA
Posts: 5,380
|
|
Not Ranked
NAPA, da Zone? That 10" size is just what the old VW Beetles took. Nuthin' special, just leetle.
__________________
Karlos
"In the Land of the Pigs, The Butcher is King"
|
10-05-2013, 04:11 PM
|
|
Senior Club Cobra Member
|
|
|
Join Date: May 2007
Location: Mesa,
AZ
Cobra Make, Engine: Contemporary Classic, 428 FE CCX 3069
Posts: 7,501
|
|
Not Ranked
Anyplace that carries parts for British Motor cars. MG, Triumph, Austin, Austin Healy, etc.
__________________
Dan in Arizona
CCX3209
"It's a great car and I love it, but it doesn't do 'SLOW' very well."
|
10-05-2013, 04:55 PM
|
|
CC Member
|
|
|
Join Date: Mar 2005
Location: Mesa,
AZ
Cobra Make, Engine: FFR from Levy Racing 302 FI w/Edelbrock Performer heads
Posts: 1,644
|
|
Not Ranked
What are wiper blades?
__________________
dave from mesa
Vietnam Vets may be eligible for medical care and disability compensation. Contact the VA if you have prostate cancer or type 2 diabetes. Finally got around to going to the VA.
|
10-05-2013, 05:09 PM
|
|
Senior Club Cobra Member
|
|
|
Join Date: Jun 2003
Location: West Linn,
OR
Cobra Make, Engine: ERA #684, 428 FE, TKO600
Posts: 1,378
|
|
Not Ranked
Try ANCO N-12R. Will have to be trimmed but not a problem. This is the rubber only. If you look closely at the existing you should be able to slide the old blade rubber out of the holder and just slide the new one in. Takes about 5 minutes including the trim job.
DonC
|
10-05-2013, 07:21 PM
|
|
CC Member
|
|
|
Join Date: Jun 2001
Location: Mesa,
AZ
Cobra Make, Engine: ERA #2119 289FIA
Posts: 5,380
|
|
Not Ranked
Don, is that before or after using the car for a stud finder?
__________________
Karlos
"In the Land of the Pigs, The Butcher is King"
|
10-05-2013, 08:47 PM
|
|
CC Member
|
|
|
Join Date: Aug 2000
Location: Glendale,
AZ
Cobra Make, Engine: SPF 468ci 550HP + 150HP NX Matching Shelby GT500 650HP
Posts: 4,208
|
|
Not Ranked
Wrong Don there Karl. I have replaced mine both ways. From Finish Line and buying a local rubber refill and trimming.
Here is another source for 9 inch blades only: Cobra Valley's Windshield Wiper Blades
AZ Bob
__________________
AZCOBRA, AZBOBS Plates & JAFMO
|
10-06-2013, 08:10 AM
|
|
CC Member
|
|
|
Join Date: Jun 2001
Location: Mesa,
AZ
Cobra Make, Engine: ERA #2119 289FIA
Posts: 5,380
|
|
Not Ranked
Oops! Sorry, DonC, I was thinking of DonM. Hate to cast aspersions where they are not warranted.
__________________
Karlos
"In the Land of the Pigs, The Butcher is King"
|
10-06-2013, 01:51 PM
|
|
CC Member
|
|
|
Join Date: Mar 2003
Location: Wickenburg AZ- PHX, Cinci, Indy before,
AZ
Cobra Make, Engine: FFR Mk 3 408 530 - 585 T- mustang Dyno at B&R
Posts: 1,836
|
|
Not Ranked
Took Karl Man and Don C advise. Napa had rubber and you slide it to the sleeve bracket and cut to proper length = $6
|
Posting Rules
|
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts
HTML code is Off
|
|
|
All times are GMT -7. The time now is 08:44 AM.
Links monetized by VigLink
|