Another new person looking at kits.

[400TT]

Agree with Rebel1.

But performance wise, you can't go past the modern rear-ends especially something like Skyline rear with it's 300mm vented rotors & 2 piston calipers. Just a fantastic unit all round and great value for money. But just not a lot of rear wheel dish on a Cobra.

[stiffy]

Hey TL,


I have a 1988 RMC (recently rebuilt thanks to too much right foot and not enough talent ) great looking car ( I used the G-FORCE body),
They are easy to drive and are one of the better older looking kits (IMO).

I have just taken delivery of a Harrison Daytona (L76/6 Speed).
If I was to build a Cobra it would most likely be a Harrison!!!

If you want to look at a number of kits speak to Doug Pearce in Lilydale (9739 4222) he has a few of every kit in differing stages of build on site for you to look at. He also has a very UGLY looking Daytona that he is converting into Jennifer Hawkins

Come along to the meeting this Thursday if you can.
7pm Club Tivoli 291 Dandenong Road Windsor

STIFFY

[Aussie Mike]

Originally Posted by stiffy

He also has a very UGLY looking Daytona that he is converting into Jennifer Hawkins

That's probably the only way you're going to get inside Jenifer Hawkins too Stiffy.

Cheers

[stiffy]

Good one Aussie,


I could get a life size blow up doll!!!


STIFFY

[Aussie Mike]

There's probably a market for one of those.

[T.L.]

Stiffy,

I will most probably be there on Thursday night, and look forward to talking to some of you guys.

TL

[T.L.]

Originally Posted by 400TT

Agree with Rebel1.

But performance wise, you can't go past the modern rear-ends especially something like Skyline rear with it's 300mm vented rotors & 2 piston calipers. Just a fantastic unit all round and great value for money. But just not a lot of rear wheel dish on a Cobra.

Craig,

So the width of the rear wheel is reduced a little is it?. Can you still run 9 1/2 -10" on there or is that pushing it with clearances for the red tape people?.

Thanks for comments

TL

[400TT]

Originally Posted by T.L.

Craig,

So the width of the rear wheel is reduced a little is it?. Can you still run 9 1/2 -10" on there or is that pushing it with clearances for the red tape people?.

Thanks for comments

TL

Sorry, should have explained it better. It's just got to do with how deep the wheel looks. How much rim is sticking out in front of the wheel centre and how much is sticking in. Nothing to do with width. So traditional Cobra look is to have lots of rim sticking outside, with Skyline rear you have what a call a medium amount of rim sticking out, with say a Classic Revival you have very little outside rim. With modern interpretation of Cobras these days, deep dish rims seem to have gone the way of the dodo anyway.

With Harrison you will breeze in 9 1/2 - 10". There have been a few Harrisons fitted with 12 1/2" rims on the rear. From measurements we took from our Harrison with Skyline rear, something like 315/35/17 was the widest tyre we could fit without modification, which is wider than most people want.

This is a Harrison built recently with 335/35/17 tyres.



And has stroked & supercharged LS1(or LS???).

[sambo]

Craig, with a bit of poking around I found some other pics of that blue monster... twin NOS bottles and one very unique interior! Is there a link to the member gallery on the QLD site? I couldn't find it. Which kit is it based on?

Cheers,
Paul

[Aussie Mike]

Rim width isn't a problem for the modern double wishbone rear ends. It's just you have to run the rear suspension at it's full width as they can prove difficult to narrow. This means you end up with not a lot of dish on the rear wheels or even a positive offset where there's more rim on the inside than the outside.

I wasn't so keen on the look at first but it's grown on me. My rear rims are 11" wide and the tyres are 315/35/17 but it doesn't look like it because there's not a lot of dish on the rear rims.

I think this is the best pic I have to illustrate it. The dish on the rear wheels is the same as the front.



Cheers

[Plums]

Here's my G-Force with Vintage Wheels in 17 x 8.5 with 235/45-17, and 17 x 10.5 with 315/35-17's...

[macloft]

I believe I have seen the car that Craig has posted and it is a beast supercharged and nitros.
What I can't understand is how is it going to pass engineering. The supercharger and nos bottles are non to subtle and the guys at the pits would be able to spot them easily.
Craig do you have any side shots of the car. When I saw it in the upholsterers my camera was flat. It appeared to have a skyline diff which (as you state) means a normal Harrison can fit those monster rear wheels.

[400TT]

Some more photos on our site.

http://www.cobracarclubqld.org.au/Ne...s/JoesNewCobra

It's definitely a Skyline rear.

It's got some Jap wheels on it, which are design to give a nice dish look with very little available offset. I forgot the name of these wheels off hand, will see if it comes to me.

[Ross Smith]

This is the "traditional" jag rear end in an RMC with shortened driveshafts to allow for dished wheels



These are australian produced 5 stud Halibrand replica wheels for those of us can't afford the real thing. (I am envious of your wheels Plums)