Club Cobra Keith Craft Motorsports  

Go Back   Club Cobra > Manufacturers, Engine Builders, tools, and parts. > Classic Roadsters II

Nevada Classics
Keith Craft Racing
Main Menu
Module Jump:
Nevada Classics
Nevada Classics
MMG Superformance
MMG Superformance
Advertise at CC
Banner Ad Rates
MMG Superformance
Keith Craft Racing
March 2024
S M T W T F S
          1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
31            
  #1 (permalink)  
Old 11-13-2017, 05:44 AM
CC Member
Visit my Photo Gallery

 
Join Date: Sep 2017
Posts: 27
Not Ranked     
Default CR parts help

Hi,
I need help as some parts of my CR have to be replaced
brake master
gas tank
gas tank sender and seal kit
gas pedal
holley carburator seal kit

thanks !!!
Attached Images
   
Reply With Quote
  #2 (permalink)  
Old 11-13-2017, 07:29 AM
G_Edmonds's Avatar
Senior Club Cobra Member
Visit my Photo Gallery

 
Join Date: May 2007
Location: Longview, Tx
Cobra Make, Engine: Classic Roadster, 408 LSX
Posts: 261
Not Ranked     
Default

I think most people use an early 70's corvette brake master cylinder.
I recently changed up my fuel system. The fuel pick-up and sender looked just like yours. I just cleaned up the float, cut off the rusty fuel tube and added another. (Actually put an in tank pump in it.) I was surprised that the tank was very clean when I opened it up. The tank is not sourced from another vehicle so you would have to find something that fits or have one made if yours is bad. Just buy some cork gasket material and cut out a sender seal. A carburetor rebuild kit for your model Holley should have all the seals you need.
Good luck.
-Greg
__________________
I've spent most of my money on cars and women. The rest I wasted.
Reply With Quote
  #3 (permalink)  
Old 11-13-2017, 07:33 AM
CC Member
Visit my Photo Gallery

 
Join Date: Sep 2017
Posts: 27
Not Ranked     
Default

Many thanks Greg, as I don't have any spec of car, is it a Holley 650 ?
Reply With Quote
  #4 (permalink)  
Old 11-13-2017, 08:25 AM
CC Member
Visit my Photo Gallery

 
Join Date: Sep 2002
Location: Milwaukee, Wi
Cobra Make, Engine: Classic Roadsters, 95 EFI 5.0
Posts: 297
Not Ranked     
Default

I don't think a specific one was used.
If you pull the carb, there should be numbers on it identifying which one it is.
For the gas tank, as said it was made specifically for the CR.
There are "gas tank coat" stuff you pour into the gas tank and swoosh it around. It creates a seal inside the gas tank. Por15 makes one and it's meant for old tanks.
http://qr.por15.com/QR-assets/downlo...TankSealer.pdf

Thinking about it, I might do this to my tank.
Reply With Quote
  #5 (permalink)  
Old 11-13-2017, 05:20 PM
CC Member
Visit my Photo Gallery

 
Join Date: Feb 2015
Location: Claremont, ca
Cobra Make, Engine: Classic, built in 1991 has a 351 Windsor single 4 bbl.
Posts: 14
Not Ranked     
Default tank sending unit

Use the search box to check on your questions, but I went through my gas tank and pulled the sending unit and just cleaned it up and reused the unit. Later I found, while searching, that the sending unit is GM and most likely a Chevy Chevette unit. Make sure you get a good ground on that sending unit or it won't work.
Reply With Quote
  #6 (permalink)  
Old 11-13-2017, 05:54 PM
joyridin''s Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Feb 2009
Posts: 1,689
Not Ranked     
Default

On the choke horn, the carb will have a list #. Copy that number and you can look it up on Holley’s web site. That should be an easy rebuild.

The master does look like an early Corvette style. If you have manual brakes, it would be an early 70’s version. You can pick them up cheap. I think I paid $15 for thr rebuilt one from the auto parts store last time I bought one.
Reply With Quote
  #7 (permalink)  
Old 11-14-2017, 01:57 AM
CC Member
Visit my Photo Gallery

 
Join Date: Sep 2017
Posts: 27
Not Ranked     
Default

many thanks...
the master has this serial stamped #5460346 and it seems to be DELCO 18M72/19176100

the tank I will make with Tankerite or POR15 and will try to fix sender
for carburetor I found CJPony Holley Carburetor Rebuild Kit 4160 Series 4V... will be suitable ?

gas pedal... any suggestion ?
Reply With Quote
  #8 (permalink)  
Old 11-14-2017, 04:42 AM
joyridin''s Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Feb 2009
Posts: 1,689
Not Ranked     
Default

I do not know about the number, but it has a large bowl in the front and rear, so it has to be from a GM car with 4 wheel disk brakes. I will put money on it that it came from a Corvette. Go to Rockauto and look up a 1972 Corvette with manual brakes and you will see quite a few options. The are in the mid $20 range.

You will need the list number to buy the correct kit unless they are selling a super generic kit. You carb is pretty nice since you have metering blocks int he front and rear. You might want to pick up a set of jet extensions for the front and rear and a cam kit. You can really make them run with a bit of fiddling.

https://www.holley.com/products/fuel...parts/122-5000
Reply With Quote
  #9 (permalink)  
Old 11-14-2017, 06:09 AM
CC Member
Visit my Photo Gallery

 
Join Date: Sep 2017
Posts: 27
Not Ranked     
Default

You are right, for master cylinder I can save $50...
For carburetor, model should be near choke housing but couln't find yet...
On valve covers there is M/T, what does it mean ? Air filter seems a bit small ?
Attached Images
 
Reply With Quote
  #10 (permalink)  
Old 11-14-2017, 06:35 AM
CC Member
Visit my Photo Gallery

 
Join Date: Feb 2015
Location: Claremont, ca
Cobra Make, Engine: Classic, built in 1991 has a 351 Windsor single 4 bbl.
Posts: 14
Not Ranked     
Default valve covers

M/T = Mickey Thompson, racing parts.
Reply With Quote
  #11 (permalink)  
Old 11-14-2017, 08:12 AM
CC Member
Visit my Photo Gallery

 
Join Date: Sep 2017
Posts: 27
Not Ranked     
Default

carburetor is Holley 4777-3 1281, 4150 650

any idea where to find stewart warner fuel sender Ohmic Range: 240 - 33.5 ?
Reply With Quote
  #12 (permalink)  
Old 11-14-2017, 08:48 AM
cycleguy55's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Feb 2014
Location: White City, SK
Cobra Make, Engine: West Coast, 460 CID
Posts: 2,844
Not Ranked     
Default

Quote:
Originally Posted by merlino69 View Post
carburetor is Holley 4777-3 1281, 4150 650

any idea where to find stewart warner fuel sender Ohmic Range: 240 - 33.5 ?
Holley kit for 4777-3: https://www.holley.com/products/fuel...t/parts/37-485

240 / 33 fuel level senders - take your pick, but note none have provisions for fuel pickup tube: https://www.summitracing.com/int/sea...illocation=int
__________________
Brian
Reply With Quote
  #13 (permalink)  
Old 11-14-2017, 09:30 AM
CC Member
Visit my Photo Gallery

 
Join Date: Sep 2017
Posts: 27
Not Ranked     
Default

I cleaned pickup tube as it's custom made, sensor is screwed to plate I would have to check lenght and curve
On sensor I have this part #835400-1 but couldn't find, gauge is SW so should be 240 / 33
Reply With Quote
  #14 (permalink)  
Old 11-15-2017, 07:32 AM
CC Member
Visit my Photo Gallery

 
Join Date: Sep 2017
Posts: 27
Not Ranked     
Default

[quote=wanab65;1432804]Use the search box to check on your questions, but I went through my gas tank and pulled the sending unit and just cleaned it up and reused the unit. Later I found, while searching, that the sending unit is GM and most likely a Chevy Chevette unit. Make sure you get a good ground on that sending unit or it won't wo

Last edited by merlino69; 11-15-2017 at 08:00 AM..
Reply With Quote
  #15 (permalink)  
Old 11-26-2017, 03:35 PM
CC Member
Visit my Photo Gallery

 
Join Date: Jul 2009
Location: Old forge, pa
Cobra Make, Engine: Classic roadsters ll
Posts: 23
Not Ranked     
Default

Hi I used a 1975 5.0 mustang master cylinder on my cr car done part # 10-1602
Reply With Quote
  #16 (permalink)  
Old 11-28-2017, 03:32 AM
CC Member
Visit my Photo Gallery

 
Join Date: Sep 2017
Posts: 27
Not Ranked     
Default

Master cylinder was from C3 Corvette, brake hoses from 1978 Mustang II
I had my tank fixed with Tankerite
Fuel level sending unit I found on Ebay Datcon type, 240-33 ohms, 6”- 24” adjustable
as gauge is from Stewart Warner and hope would work

now I have to replace all shock absorbers and rubber bushing

any idea about gas pedal ?
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 07:09 PM.


Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: CC Policy
Links monetized by VigLink