Club Cobra Gas-N Exhaust  

Go Back   Club Cobra > Manufacturers, Engine Builders, tools, and parts. > ERA---Speak with Bob Putnam

MMG Superformance
Nevada Classics
MMG Superformance
Main Menu
Module Jump:
Nevada Classics
Nevada Classics
Advertise at CC
Banner Ad Rates
Keith Craft Racing
MMG Superformance
MMG Superformance
March 2024
S M T W T F S
          1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
31            
  #1 (permalink)  
Old 11-24-2014, 10:24 AM
DanEC's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Apr 2009
Location: Little Rock area, AR
Cobra Make, Engine: ERA Street Roadster #782 with 459 cu in FE KC engine, toploader, 3.31
Posts: 4,480
Not Ranked     
Default Rear tire contact at front

I'm running a slightly oversize tire in the rear (255/60-15) and sure enough I'm noticing some contact at the fiberglass closure panels at the front of the wheelwells when I hit a really sharp dip.

I think I remember reading that the lateral links off the rear suspension hub carriers are primarily to locate the differential and wheels laterally and have little or no affect on rear alignment. So I assume I can back off the adjustment on these links, swinging the affair slightly to the rear and gain a fraction more clearance up front - is this correct?

Any limits as to how far I can or can't go with this adjustment?

Thanks

Dan
__________________
ERA 782 Running
https://www.youtube.com/watch?v=Cfge...b1-77fqwFRu7c]
Reply With Quote
  #2 (permalink)  
Old 11-24-2014, 03:32 PM
CC Member
Visit my Photo Gallery

 
Join Date: Nov 2003
Location: New Britain, CT
Cobra Make, Engine: Size 10 Feet
Posts: 2,993
Not Ranked     
Default

If you have the ERA outboard-braked rear suspension, I don't see any problem with lengthening both the upper and lower trailing arms. Even 1/4" might eliminate most of the rubbing.
Reply With Quote
  #3 (permalink)  
Old 11-24-2014, 03:36 PM
DanEC's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Apr 2009
Location: Little Rock area, AR
Cobra Make, Engine: ERA Street Roadster #782 with 459 cu in FE KC engine, toploader, 3.31
Posts: 4,480
Not Ranked     
Default

Bob - this is the standard in-board brake suspension. Does that make a difference?

I'm a little below recommended ride height and I thought if I raised the height a 1/4 in and extended the lateral lengths 3/16 to 1/4 inch that I would be OK. I may crank the shock setting up another click or two also. It has only hit on a pretty severe dip.
__________________
ERA 782 Running
https://www.youtube.com/watch?v=Cfge...b1-77fqwFRu7c]
Reply With Quote
  #4 (permalink)  
Old 11-25-2014, 05:26 AM
CC Member
Visit my Photo Gallery

 
Join Date: Nov 2003
Location: New Britain, CT
Cobra Make, Engine: Size 10 Feet
Posts: 2,993
Not Ranked     
Default

The amount you can lengthen the trailing arm is limited, since it changes the pinion angle when you do. It would be nice if you knew what your pinion angle currently is (at normal ride height). I'd try to keep that angle within 2 or 3 degrees of the tilt of the engine/trans.
Reply With Quote
  #5 (permalink)  
Old 11-25-2014, 06:59 AM
DanEC's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Apr 2009
Location: Little Rock area, AR
Cobra Make, Engine: ERA Street Roadster #782 with 459 cu in FE KC engine, toploader, 3.31
Posts: 4,480
Not Ranked     
Default

Thanks - I'll put it on my lift and see if I can determine where they are now. I have my transmission sitting pretty high on the mount which should have leveled out my transmission yoke some and may give me a bit of room to work with on the differential angle (I think ERA sets them up with the diff input sloping slightly up to the front.
__________________
ERA 782 Running
https://www.youtube.com/watch?v=Cfge...b1-77fqwFRu7c]
Reply With Quote
  #6 (permalink)  
Old 11-25-2014, 08:05 AM
kevins2's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Dec 2011
Location: West Chester, PA
Cobra Make, Engine: ERA #795 427 S/C completed Jan. '14 - '68 FE 427 side oiler
Posts: 1,032
Not Ranked     
Default

Hi Dan,

I had the same problem and Doug instructed me to lengthen the trailing arms 3/8". No more contact. I also have the transmission shimmed up higher than the manual calls for and everything seems to work well - still good clearance between the chassis and U-joint.

Kevin
__________________
"Anyone who drives faster than you is a maniac and anyone who drives slower than you is an idiot" - George Carlin
Reply With Quote
  #7 (permalink)  
Old 11-25-2014, 09:17 AM
DanEC's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Apr 2009
Location: Little Rock area, AR
Cobra Make, Engine: ERA Street Roadster #782 with 459 cu in FE KC engine, toploader, 3.31
Posts: 4,480
Not Ranked     
Default

Quote:
Originally Posted by kevins2 View Post
Hi Dan,

I had the same problem and Doug instructed me to lengthen the trailing arms 3/8". No more contact. I also have the transmission shimmed up higher than the manual calls for and everything seems to work well - still good clearance between the chassis and U-joint.

Kevin
Thanks Kevin - that gives me something to work with.

Dan
__________________
ERA 782 Running
https://www.youtube.com/watch?v=Cfge...b1-77fqwFRu7c]
Reply With Quote
  #8 (permalink)  
Old 11-10-2016, 06:35 AM
CC Member
Visit my Photo Gallery

 
Join Date: Dec 2012
Cobra Make, Engine:
Posts: 973
Not Ranked     
Default

I know this is an old thread, but I'm considering using the same tires as Dan on my ERA. My car (488) is of the older variety so the difference may be worth mentioning. I also have the standard rear and exhaust pipes in the way like Dan. I have test fitted 295/50-15 and it just hits my pipes (2.5" exhaust). I have little choice but to use the 255/60 which is a taller tire. Would I expect to have a rubbing problem? Any difference here between the old and new chassis design? Dan, did you resolve yours?
__________________
Reply With Quote
  #9 (permalink)  
Old 11-10-2016, 09:25 AM
DanEC's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Apr 2009
Location: Little Rock area, AR
Cobra Make, Engine: ERA Street Roadster #782 with 459 cu in FE KC engine, toploader, 3.31
Posts: 4,480
Not Ranked     
Default

Troy - I did perform a little adjustment (lengthening the trailing arms or struts) and lessened it greatly. Since then I've noticed a slight bit of wear on the undercoating there so apparently on a sharp dip my tire still very lightly contacts it - can't hear or feel it. It's on my list of things to do - to lengthen the arms a bit more but I either have to remove my tail pipes or release the hangars to drop it down enough in order to get the bolt out at the front of the strut. I just haven't done it yet.
__________________
ERA 782 Running
https://www.youtube.com/watch?v=Cfge...b1-77fqwFRu7c]
Reply With Quote
  #10 (permalink)  
Old 11-10-2016, 09:58 AM
CC Member
Visit my Photo Gallery

 
Join Date: Dec 2012
Cobra Make, Engine:
Posts: 973
Not Ranked     
Default

Thanks Dan. Do you have contact at both sides?
__________________
Reply With Quote
  #11 (permalink)  
Old 11-10-2016, 03:02 PM
DanEC's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Apr 2009
Location: Little Rock area, AR
Cobra Make, Engine: ERA Street Roadster #782 with 459 cu in FE KC engine, toploader, 3.31
Posts: 4,480
Not Ranked     
Default

Yes - it's pretty much the same on both sides. ERA builds a much more symmetrical car than AC probably ever did. After my first adjustment though it's just lightly kissing it - just enough to see where it scuffed a little stripe on the undercoated surface. I also still have my rear shocks a little on the soft side and I could probably stand to stiffen them up a couple of clicks.

Dan
__________________
ERA 782 Running
https://www.youtube.com/watch?v=Cfge...b1-77fqwFRu7c]
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 06:05 PM.


Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: CC Policy
Links monetized by VigLink