Keith Craft Inc.- We service what we sell!!! Check out our Cobra engines!!! We build high performance racing engines and components for the fast pace strip racing industry as well as daily drivers who want to be FIRST!!!

FE Forums sponsored by Keith Craft Inc.


Go Back   Club Cobra > Engine Building, Tuning, and Induction > FE TALK

Welcome to Club Cobra!  The World's largest non biased Shelby Cobra related site!

  •  » Representation from nearly all Cobra/Daytona/GT40 manufacturers
  •  » Help from all over the world for your questions
  •  » Build logs for you and all members
  •  » Blogs
  •  » Image Gallery
  •  » Many thousands of members and nearly 1 million posts! 

YES! I want to register an account for free right now!  p.s.: For registered members this ad will NOT show

Keith Craft Racing
Nevada Classics
Main Menu
Nevada Classics
Nevada Classics
Keith Craft Racing
Advertise at CC
Banner Ad Rates
Keith Craft Racing
Keith Craft Racing
Keith Craft Racing
MMG Superformance
March 2024
S M T W T F S
          1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
31            

Kirkham Motorsports

Like Tree7Likes

Reply
 
LinkBack Thread Tools Rate Thread Display Modes
  #21 (permalink)  
Old 06-08-2018, 02:08 PM
cycleguy55's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Feb 2014
Location: White City, SK
Cobra Make, Engine: West Coast, 460 CID
Posts: 2,844
Not Ranked     
Default

Quote:
Originally Posted by Spyglass View Post
I recently bought an ERA with a 428, it's 5 years old and has approx 3,000 total miles on it, I understand the engine build is:

Believed to be a 1968 block
Scat 4.250 rotating assembly, 462 ci
Mahle forged Pistons
Edelbrock Performer RPM heads
9.5 to 1 CR
Edelbrock intake
Holley 750
MSD distributor
Howard hydraulic roller cam
Harland Sharp rocker assembly
Canton road race oil pan

I've driven the car approx 500 miles and experienced a progressively worsening oil leak(s) and misfiring under load. The oil leak(s) appear to be coming from the upper front drivers side of the engine, I've replaced the fuel pump gasket and managed to get 1/4 turn by hand on the remote oil filter, both of which appeared to be culprits. I haven't driven it since to know if this has cured the leaks.

The misfire is of greater concern, the engine starts, idles and runs fine at light throttle applications. However when I accelerate harder, say 1/2 throttle and 2500 to 3000 rpm the engine starts to misfire/stumble, it will continue to pull through the misfire. On the few occasions I've accelerated at full throttle, it again misfires/stumbles, then appears to clear itself and when I look in the rear view mirror there is a large blue cloud of smoke in the road. I don't think this is a constant trail of smoke, rather a single cloud that's blown out.

Apologies for the very long post, if you've managed to read this far, do you have any ideas or suggestions as to what's wrong?

Thanks in advance for any assistance.
Regards
Kevin

I had a similar problem when I replaced my old MSD analog box with a new digital box from Summit Racing (supposedly built by MSD). It would cruise fine and full throttle wasn't a problem, but partial throttle acceleration was a bad misfire. It seems the part-throttle acceleration was giving me both vacuum and centrifugal advance - too much in a relatively light car. Full throttle dropped the vacuum and eliminated the effect of the vacuum advance, hence the reason the engine ran fine there.



Perhaps the problem didn't show up on the old analog ignition because it was 'slower' in responding to ignition signals than the newer digital box, but that's merely conjecture on my part.



Solution was to eliminate the vacuum advance and go strictly centrifugal.
Spyglass likes this.
__________________
Brian
Reply With Quote
  #22 (permalink)  
Old 06-08-2018, 02:32 PM
CC Member
Visit my Photo Gallery

 
Join Date: Apr 1999
Location: cleveland, OH
Cobra Make, Engine: CSX4000, 427
Posts: 1,999
Not Ranked     
Default

I've had more problems with MSD than anything else, corrosion, malfunction, etc. Won't buy another. You need to drill the cap to vent the ozone to prevent corrosion, misfires.
__________________
"After jumping into an early lead, Miles pitted for no reason. He let the entire field go by before re-entering the race. The crowd was jumping up and down as he stunned the Chevrolet drivers by easily passing the entire field to finish second behind MacDonald's other team Cobra. The Corvette people were completely demoralized."
Reply With Quote
  #23 (permalink)  
Old 06-11-2018, 10:49 AM
CC Member
Visit my Photo Gallery

 
Join Date: Feb 2016
Location: Katy, TX
Cobra Make, Engine: ERA, stroked 428FE (462ci)
Posts: 33
Not Ranked     
Default

Guys, thanks for all of the replies and suggestions.

Unfortunately I had a busy weekend so not much time dedicated to the Cobra. The replacement fuel pump gasket and oil filter seal appears to have cured the oil leak. I removed the PCV valve, cleaned with WD40, manually manipulated it and reinstalled. Removed the plugs and they looked OK, but difficult to really judge as I'd run the engine to move the car around the garage earlier in the week.

I went for a quick drive on Sunday evening (it's currently too hot here to drive it during the day!) and whilst traffic prevented a full test, the misfire appears to have gone. I won't declare this resolved yet, but it certainly seems to running better. Does it make sense that the PCV valve could have cause this?

Stay tuned and thanks for the contributions.

Kevin
Reply With Quote
  #24 (permalink)  
Old 06-11-2018, 10:57 AM
patrickt's Avatar
Half-Ass Member
Visit my Photo Gallery

 
Join Date: Jun 2005
Cobra Make, Engine: ERA #732, 428FE (447 CID), TKO600, Solid Flat Tappet Cam, Tons of Aluminum
Posts: 21,888
Not Ranked     
Default

Quote:
Originally Posted by Spyglass View Post
Does it make sense that the PCV valve could have cause this?
Not really. But any time you start pulling hoses, pulling plugs, and the like you stand the chance of "fixing" a poor connection, shorting plug wire, or the like. On the bright side, if you can get the problem to go away, even for just a short while, by effectively "fiddling" with stuff, then the problem is not a bad one... it just has to be found. It could all be as simple as a temperamental coil or plug wire that works fine when it's in one position, but is intermittently crappy in another. Back in the old days, if you just had plug wires 7 and 8 resting too close to one another on an FE you could get a misfire.
Spyglass likes this.
Reply With Quote
  #25 (permalink)  
Old 06-11-2018, 04:03 PM
FWB's Avatar
FWB FWB is offline
CC Member
Visit my Photo Gallery

 
Join Date: Jan 2008
Location: Williamsport, PA
Cobra Make, Engine: Kellison Stallion 468 FE
Posts: 2,703
Not Ranked     
Default

Quote:
Originally Posted by patrickt View Post
Not really. But any time you start pulling hoses, pulling plugs, and the like you stand the chance of "fixing" a poor connection, shorting plug wire, or the like. On the bright side, if you can get the problem to go away, even for just a short while, by effectively "fiddling" with stuff, then the problem is not a bad one... it just has to be found. It could all be as simple as a temperamental coil or plug wire that works fine when it's in one position, but is intermittently crappy in another. Back in the old days, if you just had plug wires 7 and 8 resting too close to one another on an FE you could get a misfire.



Damn it i hate agreeing with Patrick........but i must
__________________
Fred B
Reply With Quote
  #26 (permalink)  
Old 06-12-2018, 07:46 AM
CC Member
Visit my Photo Gallery

 
Join Date: Feb 2016
Location: Katy, TX
Cobra Make, Engine: ERA, stroked 428FE (462ci)
Posts: 33
Not Ranked     
Default

Quote:
Originally Posted by spdbrake View Post
Curious if you have vac advance on your distributor?
You mentioned easing into the throttle (vac advance would be pulling max advance still) and it runs fine.
Then you mentioned when throttle up aggressively you get the misfire (vac advance will not be helping the the timing will be retarded quite a bit).

You may have phasing issue in the dizzy where your too much advance or too much timing retard (your rotor is in between spark plug posts). This is a problem more common on small diameter distributors and can cause scatter and crossfire.

https://www.youtube.com/watch?v=aWMlNwGW0tM

Bad phasing and crossfire
https://www.youtube.com/watch?v=zulDzQ5q9TM

Everything You Wanted to Know About Vacuum Advance and Ignition Timing
Good info, thanks. Not sure whether I have a vacuum advance on the distributor, I'll check. Since the issue may now have moved to the dreaded intermittent category, this may not be the issue. Appreciate your input.
Reply With Quote
  #27 (permalink)  
Old 06-12-2018, 01:35 PM
Texasdoc's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Feb 2012
Location: Keller, TX
Cobra Make, Engine: Lonestar Classics LS427. Self-built 408W, AFR 195 heads, Performer RPM Intake, Quick Fuel 750, 407rwhp, 479rwtq
Posts: 549
Not Ranked     
Default

Hope it's gone. But another thing to check with a misfire over 3000 is to check your valve springs. Ask me how I know.
Reply With Quote
  #28 (permalink)  
Old 06-14-2018, 02:35 PM
CC Member
Visit my Photo Gallery

 
Join Date: Jan 2012
Location: Katy, Tx
Cobra Make, Engine: ERA#134 427 Ctr oiler 2x4's
Posts: 50
Not Ranked     
Default

Next time you're under the distributor cap, check for corrosion. Changing the cap cleared up a lot of hard starting/backfire issues on mine.
Reply With Quote
  #29 (permalink)  
Old 06-14-2018, 02:37 PM
CC Member
Visit my Photo Gallery

 
Join Date: Jan 2012
Location: Katy, Tx
Cobra Make, Engine: ERA#134 427 Ctr oiler 2x4's
Posts: 50
Not Ranked     
Default

Where in Katy? I'm in Grayson Lakes.
Reply With Quote
  #30 (permalink)  
Old 06-14-2018, 03:28 PM
CC Member
Visit my Photo Gallery

 
Join Date: Feb 2016
Location: Katy, TX
Cobra Make, Engine: ERA, stroked 428FE (462ci)
Posts: 33
Not Ranked     
Default

Quote:
Originally Posted by LG57 View Post
Next time you're under the distributor cap, check for corrosion. Changing the cap cleared up a lot of hard starting/backfire issues on mine.

Thanks, I'll add it to the list, hopefully this weekend I 'll have a chance to spend more time on the Cobra. I've still got a few of odds and ends to do on the house following the post-flood reconstruction. You just know which one my wife thinks should take priority
Reply With Quote
  #31 (permalink)  
Old 06-14-2018, 03:34 PM
CC Member
Visit my Photo Gallery

 
Join Date: Feb 2016
Location: Katy, TX
Cobra Make, Engine: ERA, stroked 428FE (462ci)
Posts: 33
Not Ranked     
Default

Quote:
Originally Posted by LG57 View Post
Where in Katy? I'm in Grayson Lakes.
We're pretty close, I ride my bike past your sub-division every Saturday morning. I'm at South Fry and Westgreen.

How long have you had your ERA? We should get together sometime.
Reply With Quote
  #32 (permalink)  
Old 06-19-2018, 08:17 AM
Danr55's Avatar
Senior Club Cobra Member
Visit my Photo Gallery

 
Join Date: May 2007
Location: Mesa, AZ
Cobra Make, Engine: Contemporary Classic, 428 FE CCX 3069
Posts: 7,500
Not Ranked     
Default

I was going to "kind of" agree with Patrick. Have you tried setting up in a dark garage and accelerating to see if you were sparking between plug wires or between plug wires and valve covers, block, etc?
__________________


Dan in Arizona
CCX3209


"It's a great car and I love it, but it doesn't do 'SLOW' very well."
Reply With Quote
  #33 (permalink)  
Old 08-15-2018, 12:19 PM
CC Member
Visit my Photo Gallery

 
Join Date: Feb 2016
Location: Katy, TX
Cobra Make, Engine: ERA, stroked 428FE (462ci)
Posts: 33
Not Ranked     
Default

After a lot of traveling I'm back on the Cobra oil burning and miss fire investigation.

It still starts, idles and runs fine below 2,500 rpm and low throttle applications. However as soon as you get into the throttle it exhibits a variety of behaviors, all of which can all be experience in one drive. These can be:

1. 1/4 to 1/2 throttle acceleration, engine stumbles/misses but no obvious smoke from exhaust. I can't be 100% sure about this as it's difficult to see.

2. 1/2 to full throttle acceleration, engine stumbles/misses (more pronounced), seems to clear and blows out a huge continuous trail of blue smoke from both exhausts that is clearly visible in the mirror - it literally fills the road behind.

3. 1/2 to full throttle acceleration, engine stumbles/misses (more pronounced), blows out a single huge burp of blue smoke that's clearly visible in the mirror, seems to clear and car accelerates hard.

4. 1/2 to full throttle acceleration, slight engine stumbles/misses, car accelerates hard (as you'd expect), no obvious smoke visible in the mirror.

It doesn't seem consistent, or perhaps I'm not being very scientific in my testing, which is entirely possible.

I removed all eight plugs, they all had similar oil and carbon residue, see the attached photo. Between my oil leaks and oil burning, I'm using about a quart of oil every 300 - 400 miles.

Any ideas or recommendations for an FE specialist in the Houston areas I can take the car to?

Thanks
Kevin

Reply With Quote
  #34 (permalink)  
Old 08-15-2018, 03:25 PM
patrickt's Avatar
Half-Ass Member
Visit my Photo Gallery

 
Join Date: Jun 2005
Cobra Make, Engine: ERA #732, 428FE (447 CID), TKO600, Solid Flat Tappet Cam, Tons of Aluminum
Posts: 21,888
Not Ranked     
Default

Quote:
Originally Posted by Spyglass View Post
Between my oil leaks and oil burning, I'm using about a quart of oil every 300 - 400 miles.
That's a lot of oil. If it were me, I would disconnect the PCV, and cap it off so you don't have a vacuum leak, then bolt on a known-good carb and take her for another spin. I know that's not as easy as it sounds, but usually someone in your local Cobra club has a known-to-be-decent Holley 750 sitting up on his shelf to loan out.
Reply With Quote
  #35 (permalink)  
Old 08-15-2018, 03:46 PM
FWB's Avatar
FWB FWB is offline
CC Member
Visit my Photo Gallery

 
Join Date: Jan 2008
Location: Williamsport, PA
Cobra Make, Engine: Kellison Stallion 468 FE
Posts: 2,703
Not Ranked     
Default

Quote:
Originally Posted by Danr55 View Post
I was going to "kind of" agree with Patrick. Have you tried setting up in a dark garage and accelerating to see if you were sparking between plug wires or between plug wires and valve covers, block, etc?

will that keep me from agreeing with Patrick?....
__________________
Fred B
Reply With Quote
  #36 (permalink)  
Old 08-15-2018, 03:50 PM
FWB's Avatar
FWB FWB is offline
CC Member
Visit my Photo Gallery

 
Join Date: Jan 2008
Location: Williamsport, PA
Cobra Make, Engine: Kellison Stallion 468 FE
Posts: 2,703
Not Ranked     
Default

Quote:
Originally Posted by Spyglass View Post
After a lot of traveling I'm back on the Cobra oil burning and miss fire investigation.

It still starts, idles and runs fine below 2,500 rpm and low throttle applications. However as soon as you get into the throttle it exhibits a variety of behaviors, all of which can all be experience in one drive. These can be:

1. 1/4 to 1/2 throttle acceleration, engine stumbles/misses but no obvious smoke from exhaust. I can't be 100% sure about this as it's difficult to see.

2. 1/2 to full throttle acceleration, engine stumbles/misses (more pronounced), seems to clear and blows out a huge continuous trail of blue smoke from both exhausts that is clearly visible in the mirror - it literally fills the road behind.

3. 1/2 to full throttle acceleration, engine stumbles/misses (more pronounced), blows out a single huge burp of blue smoke that's clearly visible in the mirror, seems to clear and car accelerates hard.

4. 1/2 to full throttle acceleration, slight engine stumbles/misses, car accelerates hard (as you'd expect), no obvious smoke visible in the mirror.

It doesn't seem consistent, or perhaps I'm not being very scientific in my testing, which is entirely possible.

I removed all eight plugs, they all had similar oil and carbon residue, see the attached photo. Between my oil leaks and oil burning, I'm using about a quart of oil every 300 - 400 miles.

Any ideas or recommendations for an FE specialist in the Houston areas I can take the car to?

Thanks
Kevin


that much oil consumption i would guess the intake is leaking. Can't help you with a recommendation for someone in Houston, i can recommend someone in San Antonio area.
__________________
Fred B
Reply With Quote
  #37 (permalink)  
Old 08-15-2018, 09:32 PM
CC Member
Visit my Photo Gallery

 
Join Date: Apr 2016
Cobra Make, Engine:
Posts: 92
Not Ranked     
Default

Does your MSD have a vacuum advance hose? Disconnect it and drive it.. Sounds like your distributor advance is not working properly.
Reply With Quote
  #38 (permalink)  
Old 08-15-2018, 10:36 PM
Gaz64's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: May 2008
Location: Brisbane, QLD
Cobra Make, Engine:
Posts: 2,773
Not Ranked     
Default

AS patrick has said, disconnect the PCV hose from the base of the carb, plug the carb nipple, replace the spark plugs with a fresh set.

If all the plugs look like that, I would be very concerned about the engine build quality.
__________________
Gary

Gold Certified Holden Technician
Reply With Quote
  #39 (permalink)  
Old 08-16-2018, 04:57 AM
Danr55's Avatar
Senior Club Cobra Member
Visit my Photo Gallery

 
Join Date: May 2007
Location: Mesa, AZ
Cobra Make, Engine: Contemporary Classic, 428 FE CCX 3069
Posts: 7,500
Not Ranked     
Default

Have you done a compression test on the motor?
__________________


Dan in Arizona
CCX3209


"It's a great car and I love it, but it doesn't do 'SLOW' very well."
Reply With Quote
  #40 (permalink)  
Old 08-16-2018, 09:17 AM
patrickt's Avatar
Half-Ass Member
Visit my Photo Gallery

 
Join Date: Jun 2005
Cobra Make, Engine: ERA #732, 428FE (447 CID), TKO600, Solid Flat Tappet Cam, Tons of Aluminum
Posts: 21,888
Not Ranked     
Default

Yeah, maybe start out really simple by just disconnecting the PCV and put in a fresh set of plugs, forget the carb switch for now. That's a lot of oil going somewhere and, if you're really lucky, you've just got a big glob of it coming in the base of the carb through the PCV, then it hits the plugs, causes a misfire, then it burns it all off, scares the people behind you that you're on fire or something, and then it runs good for a while before it does it again. Maybe.
Reply With Quote
Reply


Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 04:48 AM.


Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: CC Policy