Club Cobra Gas - N Exhaust  

Go Back   Club Cobra > General Discussion > Lounge

MMG Superformance
Nevada Classics
Main Menu
Module Jump:
Nevada Classics
Nevada Classics
MMG Superformance
Keith Craft Racing
Advertise at CC
Banner Ad Rates
Keith Craft Racing
MMG Superformance
MMG Superformance
June 2026
S M T W T F S
  1 2 3 4 5 6
7 8 9 10 11 12 13
14 15 16 17 18 19 20
21 22 23 24 25 26 27
28 29 30        

Kirkham Motorsports

 
 
LinkBack Thread Tools Rate Thread Display Modes
Prev Previous Post   Next Post Next
  #34 (permalink)  
Old 02-28-2009, 10:01 AM
CC Member
Visit my Photo Gallery

 
Join Date: Oct 1999
Location: Bismarck, North Dakota, USA,
Posts: 920
Not Ranked     
Red face

Quote:
Originally Posted by Ron61 View Post
Wes & Bill,

I have a question. The railroad runs about 3/4ths of a mile from my house and every once in a while I will hear a train go by with a wheel bearing screaming so loud that you can hear it all the way up into the canyons. Now I know from my uncle that used to work on the railroad that they can seize and cause problems. But the nearest rail yards that I am aware of are in Roseville, several miles South of here and I am not sure if there is one this side of Portland or not. So what happens if one of those bearings does seize while out in the canyons?

Ron
What you are probably hearing is a flange dragging. The trucks on the railcars are connected pivot-wise to the spine frame by a bolster pin. It is similar to a fifth wheel on a truck/trailer and the term may even be derived from such, 4 wheel bearings and a fifth bearing bolster. A lot of our language came from early rail terms.

Often the pin is not well lubed causing the truck wheels to resist steering. This causes the wheel flange to drag on the side of the rail during any small curvature. Normally the wheel faces are slightly tapered to cause them to seek center on the pair of rails. The flange is only to prevent derailment when the self-centering fails. In extreme cases, the flange climbs the rail and a derailment does result.

Old cars are harder to pull because of worn, dry pins and worn wheel taper. An engineer familiar with his territory knows this because a greater throttle notch (for the weight) than normal is required. It is always a concern whether some sticking brakes are dragging or flanges drag around curves. Curves are the key, since the drag is worse. Sticking brakes also pull hard in a straight line.

If a wheel bearing is actually squealing, check your trusty American Flag to observe wind direction. All the worst stuff in the world goes by rail. If you see a cloud, you will know which way to go. That's do what we do. Run. Sure, we are supposed to be ready to furnish the Hazmat Response Team info on what-is-where on the train, but we may be faced with carrying our light coffee thermos as opposed to the heavy paperwork.

Experienced teams know we will be on an upwind hill about 2 or more miles away. That is if they can find us. Our new portable radios no longer reach 2 miles, not even a train-length. Maybe on a hill away from metal. Then we could tell them where the paperwork is. Or was ...in case of locomotive fire. All this is pre-planned by government agencies as well as they do for hurricanes.

Your house is three quarter mile away? Have you considered investing in some handy bed-side gas masks and rubber suits? Me either. I live less than a half mile away.

Wes

...
Reply With Quote
 


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 08:49 PM.


Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2026, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: CC Policy
Links monetized by VigLink