Club Cobra Keith Craft Motorsports  

Go Back   Club Cobra > Manufacturers, Engine Builders, tools, and parts. > Shell Valley Companies

Keith Craft Racing
Nevada Classics
MMG Superformance
Main Menu
Module Jump:
Nevada Classics
Nevada Classics
Keith Craft Racing
Advertise at CC
Banner Ad Rates
MMG Superformance
MMG Superformance
MMG Superformance
March 2024
S M T W T F S
          1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
31            
  #1 (permalink)  
Old 01-02-2005, 11:29 AM
CC Member
Visit my Photo Gallery

 
Join Date: Dec 2001
Location: Louisville, KY
Cobra Make, Engine: I'm Cobra-less!
Posts: 9,389
Send a message via AIM to blykins
Not Ranked     
Default Shell Valley Owners...

What are these tabs for? I've searched in the manual, but can't find it. I was going to use them to bolt my lap belts to. My car is way above the stage in the picture below, but this is the only picture I could find to illustrate what I was talking about.
Attached Images
 
__________________
www.lykinsmotorsports.com
Reply With Quote
  #2 (permalink)  
Old 01-02-2005, 12:21 PM
CC Member
Visit my Photo Gallery

 
Join Date: Mar 2002
Cobra Make, Engine:
Posts: 302
Not Ranked     
Default

I'm pretty sure that the lap anchors on my 5-points are bolted to those, but it's been a while since I've had the car on the lift. If you want, I can head across the street & jerk it in the air & get back to you. (?)
Reply With Quote
  #3 (permalink)  
Old 01-02-2005, 12:25 PM
CC Member
Visit my Photo Gallery

 
Join Date: Dec 2001
Location: Louisville, KY
Cobra Make, Engine: I'm Cobra-less!
Posts: 9,389
Send a message via AIM to blykins
Not Ranked     
Default

Nah, that sounds like a lot of trouble. I'd say that's what they're for.....I can't think of anything else except for a driveshaft safety loop on those tabs in the back of the picture.

Do you remember how you mounted the shoulder harness? Is it mounted to the rollbar, or did you go through the bulkhead and mount in the trunk?
__________________
www.lykinsmotorsports.com
Reply With Quote
  #4 (permalink)  
Old 01-02-2005, 12:54 PM
CC Member
Visit my Photo Gallery

 
Join Date: Oct 2003
Location: Spokane, WA
Cobra Make, Engine: Shell Valley, 351W
Posts: 183
Not Ranked     
Default

When I visited SV quite awhile back, Dana mentioned that those points were there to mount the lap belts.

For my shoulder belts, I'm going to make a setup similar to what SV and Finishline sells that mounts on the roll bar. I'm going to put it under the deck though.

Sydney
Reply With Quote
  #5 (permalink)  
Old 01-02-2005, 01:06 PM
CC Member
Visit my Photo Gallery

 
Join Date: Dec 2001
Location: Louisville, KY
Cobra Make, Engine: I'm Cobra-less!
Posts: 9,389
Send a message via AIM to blykins
Not Ranked     
Default

What about for the passenger side?

I would use a rollbar setup, but mine bolt in. So I have to figure some way of just drilling a hole somewhere inline with the y part of the harness and bolting it down.
__________________
www.lykinsmotorsports.com
Reply With Quote
  #6 (permalink)  
Old 01-02-2005, 01:27 PM
CC Member
Visit my Photo Gallery

 
Join Date: Dec 2001
Location: Louisville, KY
Cobra Make, Engine: I'm Cobra-less!
Posts: 9,389
Send a message via AIM to blykins
Not Ranked     
Default I may go this route....

I think I may go this route:

In the picture below, at the end of the arrow is a straight portion of frame directly under the trunk. (This is a picture from ravedemon.)

I'm going to drill there on each side. That should be pretty well inline with the "y" part of the shoulder harness. I'll drill through the whole thing and just run a bolt down through it.

My body is on the car, so I guess I'll drill up from the bottom. I don't have a right angle drill motor, so that's my only choice.

I wouldn't think it would weaken the frame at that point. SV drills through the main frame rails to attach the cowl hoop....
Attached Images
 
__________________
www.lykinsmotorsports.com

Last edited by blykins; 01-02-2005 at 01:31 PM..
Reply With Quote
  #7 (permalink)  
Old 01-02-2005, 03:50 PM
CC Member
Visit my Photo Gallery

 
Join Date: Oct 2003
Location: Spokane, WA
Cobra Make, Engine: Shell Valley, 351W
Posts: 183
Not Ranked     
Default

I don't see why that idea wouldn't work. The frame is very thick in that area. Would you be running the belt under the trunk floor or in the trunk?

I'm doing the dual roll bar thing, so I'm lucky enough to have quite a few more options.

Sydney
Reply With Quote
  #8 (permalink)  
Old 01-02-2005, 04:19 PM
CC Member
Visit my Photo Gallery

 
Join Date: Dec 2001
Location: Louisville, KY
Cobra Make, Engine: I'm Cobra-less!
Posts: 9,389
Send a message via AIM to blykins
Not Ranked     
Default

I'm thinking it will go over the trunk floor, since I'll be entering from probably around 2-3" (guestimating) from the top of the bulkhead. However you won't see much sticking through. That point that I'm showing in the pic above isn't too much further back than the rollbar legs going through the trunk. So you won't see much at all of the harness.
__________________
www.lykinsmotorsports.com
Reply With Quote
  #9 (permalink)  
Old 01-02-2005, 04:40 PM
CC Member
Visit my Photo Gallery

 
Join Date: Oct 2003
Location: Spokane, WA
Cobra Make, Engine: Shell Valley, 351W
Posts: 183
Not Ranked     
Default

I guess I'm thinking if you go that route, you might need to fill the 1 1/2" gap between the trunk floor and the frame where your bolt goes through so it can be properly torqued.
Reply With Quote
  #10 (permalink)  
Old 01-02-2005, 04:46 PM
CC Member
Visit my Photo Gallery

 
Join Date: Dec 2001
Location: Louisville, KY
Cobra Make, Engine: I'm Cobra-less!
Posts: 9,389
Send a message via AIM to blykins
Not Ranked     
Default

Oh, you mean put some spacers in between so the bolt head won't bust the fiberglass when I tighten it down?
__________________
www.lykinsmotorsports.com
Reply With Quote
  #11 (permalink)  
Old 01-02-2005, 04:54 PM
CC Member
Visit my Photo Gallery

 
Join Date: Oct 2003
Location: Spokane, WA
Cobra Make, Engine: Shell Valley, 351W
Posts: 183
Not Ranked     
Default

Yeah, that's it!
Reply With Quote
  #12 (permalink)  
Old 01-03-2005, 08:25 PM
CC Member
Visit my Photo Gallery

 
Join Date: Apr 2001
Location: Abe Lincolns Birthplace, Ky
Cobra Make, Engine: CSX4761, KCR Shelby Alloy 496,760hp
Posts: 867
Send a message via AIM to misfit41
Not Ranked     
Default

you dont want a shoulder harness on the passenger side without a roll bar,,lap belt only.,,Tim
__________________
Tk



"this whole Adult thing just isnt working for me "
Reply With Quote
  #13 (permalink)  
Old 01-04-2005, 01:29 PM
CC Member
Visit my Photo Gallery

 
Join Date: Dec 2001
Location: Louisville, KY
Cobra Make, Engine: I'm Cobra-less!
Posts: 9,389
Send a message via AIM to blykins
Not Ranked     
Default

Why not, Tim? I think if you told someone that the driver had a shoulder harness and the passenger didn't....no one would ride with you.
__________________
www.lykinsmotorsports.com
Reply With Quote
  #14 (permalink)  
Old 01-07-2005, 06:22 AM
Terry Stapley's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Oct 2003
Location: Saratoga Springs, UT
Cobra Make, Engine: Shell Valley, 418W, tremec 3550tko, 9" ford rear, 3.0 gear, silver/black
Posts: 408
Not Ranked     
Default

Brent, I did mine the way you are thinking and it worked out great. The tabs in the first photo are for the belt mounts! I drilled a hole through the frame kickup and put a hole in the upper trunk bottom so the belts bolt directly to the frame. Just enlarge the hole for the rollbar support on the drivers side.
__________________
Terry
Reply With Quote
Reply

Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 10:36 AM.


Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: CC Policy
Links monetized by VigLink