SUPPORT OUR SPONSOR

Go Back   Club Cobra > Club Cobra Tech Areas > Shop Talk

Welcome to Club Cobra!  The World's largest non biased Shelby Cobra related site!

  •  » Representation from nearly all Cobra/Daytona/GT40 manufacturers
  •  » Help from all over the world for your questions
  •  » Build logs for you and all members
  •  » Blogs
  •  » Image Gallery
  •  » Many thousands of members and nearly 1 million posts! 

YES! I want to register an account for free right now!  p.s.: For registered members this ad will NOT show

Keith Craft Racing
Nevada Classics
MMG Superformance
Main Menu
Nevada Classics
Nevada Classics
Keith Craft Racing
Keith Craft Racing
Advertise at CC
Banner Ad Rates
Keith Craft Racing
MMG Superformance
March 2024
S M T W T F S
          1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
31            
  #1 (permalink)  
Old 06-29-2014, 02:52 PM
CC Member
Visit my Photo Gallery

 
Join Date: Apr 2014
Cobra Make, Engine: ERA 289 FIA 351W, B & B 427 Cobra, 331 Stroker,
Posts: 150
Not Ranked     
Default Adjusting Ford 9" Rear Axle in B & B Cobra

I'm in the finishing stages of the rebuild on my B & B Cobra and have some questions about the rear end alignment. I took the car in to have the front alignment done( just replaced the front end with tubular arms and coil overs) and was told by the alignment guy that the rear end was out of specs. I took the car home did some measurements and found the axle sits 1/2" to the left of center and the front to back measurements has the right side a 1/4" longer then the left. My question is this...should I just run it? Is it "out of specs" to the point I'll notice handling-wise or tire wear-wise? Should I take the time and money to get adjustable upper control arms and try to correct the axle position? I already have adjustable lower arms but I believe they are only good for setting pinion angle? Can the upper arms be adjusted to correct off-center AND front to back measurements independently? Considering the geometry of the 4 link system, it seems to correct for one would effect the other, not necessarily in the direction desired. I don't mind doing the work and the cost is minimal, as long as it's something worth doing and I don't end up chasing my tail. Thanks for throwing in what you got..always appreciate the help.

Kim
Reply With Quote
  #2 (permalink)  
Old 06-30-2014, 12:46 AM
CC Member
Visit my Photo Gallery

 
Join Date: Jan 2004
Location: Bavaria,
Posts: 325
Not Ranked     
Default

Kim, I don't think the adjustable uppers will help a lot in correcting the position if the axle is not centered.

I'd get a new axle housing. There are several companies that offer 9" housings custom-made to your specs. They're not that expensive: 9" Ford Fox Body Mustang Axle Housing 9 inch Rearend | eBay

Simon
Reply With Quote
  #3 (permalink)  
Old 06-30-2014, 06:16 AM
Dwight's Avatar
Senior Club Cobra Member
Visit my Photo Gallery

 
Join Date: May 2001
Location: Florence, AL
Cobra Make, Engine: RCR GT 40 & 1966 Fairlane 390 5 speed
Posts: 4,511
Not Ranked     
Smile

you can correct the front to rear 1/4" problem by cutting a 1/4" out of the lower control arm.
to move the rear end 1/2" is harder. Look at the way to upper and lowers are installed. Sometimes washers are used as spacers.
The front to the rear measurement is important but I think the side to side no so for a street car.

Call Barry McGill
sorry I don't have his number but I'm sure someone will have it.

Dwight
__________________
''Life's tough.....it's even tougher if you're stupid.'' ~ John Wayne
"Happiness Is A Belt-Fed Weapon"
life's goal should be; "to be smarter than inanimate objects"
Reply With Quote
  #4 (permalink)  
Old 06-30-2014, 08:11 AM
CC Member
Visit my Photo Gallery

 
Join Date: Apr 2014
Cobra Make, Engine: ERA 289 FIA 351W, B & B 427 Cobra, 331 Stroker,
Posts: 150
Not Ranked     
Default

The axle housing doesnt appear ro be bent. I have adjustable lower arms but found they only tilt the diff housing...the upper arms keep the diff in a solid position left to right and front to back. No spacers/washers to play with in the uppers to reposition side to side.
Reply With Quote
  #5 (permalink)  
Old 06-30-2014, 08:19 AM
Wbulk's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: May 2009
Location: American Fork, Ut
Cobra Make, Engine: 66 Cobra
Posts: 930
Not Ranked     
Default

Double post. See below.
__________________
Wayne

"Everything is alive. If you get angry at a vehicle or the trans, it won't fix until you apologize and say you are sorry." "The vehicle always knows what it is doing and what the cause of it's bad feeling is. If you ask it humbly what the problem is, it will tell you. Then you and it will both be happy."

Gil Younger
Reply With Quote
  #6 (permalink)  
Old 06-30-2014, 08:27 AM
Wbulk's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: May 2009
Location: American Fork, Ut
Cobra Make, Engine: 66 Cobra
Posts: 930
Not Ranked     
Default

Kim, I can help you with that. It is totally adjustable if you have heim joints and contingent on the arms being the right length. Which there has been a problem in the past. By coincidence I am readjusting mine right now. The lower arms set the wheel base and squareness with the frame. The upper arms set the pinion angle and center the axle between the wheel wells or frame. I hope your axle is straight. I had to have Currie straighten mine.

It can be an involved process but you can do it. It would take to long to write it here. Send me a PM with your ph number and we can talk on the phone. I am retired and am available most of the time.

Added: Sent you a PM with my number.
__________________
Wayne

"Everything is alive. If you get angry at a vehicle or the trans, it won't fix until you apologize and say you are sorry." "The vehicle always knows what it is doing and what the cause of it's bad feeling is. If you ask it humbly what the problem is, it will tell you. Then you and it will both be happy."

Gil Younger
Reply With Quote
  #7 (permalink)  
Old 06-30-2014, 09:36 AM
Rick Parker's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: May 2001
Location: California, Ca
Cobra Make, Engine: NAF 289 Slabside Early Comp Car with 289 Webers and all the goodies. Cancelling the efforts of several Priuses
Posts: 6,592
Not Ranked     
Default

Akinbeau:

Left as it is this will affect handling. Enlist the help of someone familiar with chassis design. You must verify the pivot mount dimensions through an "X" measurement from the front lower control arm mounting points, they must be exactly the same. Once this is confirmed you can THEN modify as necessary the locating mounts on the axle housing. The upper and lower rods that control the pinion angle can use threaded ends with rubber bushings (street rod fare) or high quality Rod ends (Hiem Joints). Use a RH & a LH on each rod so the tube can be rotated and effect the overall length of each rod as needed. This IS crucial to the oveall handling of the car. The Panard Bar must allow for dimensional change also.

Here is an example:

__________________
Rick

As you slide down the Banister of Life, may the splinters never be pointing the wrong way
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 03:18 AM.


Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: CC Policy