SUPPORT OUR SPONSOR

Go Back   Club Cobra > Club Cobra Tech Areas > Shop Talk

Welcome to Club Cobra!  The World's largest non biased Shelby Cobra related site!

  •  » Representation from nearly all Cobra/Daytona/GT40 manufacturers
  •  » Help from all over the world for your questions
  •  » Build logs for you and all members
  •  » Blogs
  •  » Image Gallery
  •  » Many thousands of members and nearly 1 million posts! 

YES! I want to register an account for free right now!  p.s.: For registered members this ad will NOT show

Nevada Classics
Main Menu
Nevada Classics
Nevada Classics
MMG Superformance
Keith Craft Racing
Advertise at CC
Banner Ad Rates
MMG Superformance
MMG Superformance
MMG Superformance
March 2024
S M T W T F S
          1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
31            

Kirkham Motorsports

Like Tree22Likes

Reply
 
LinkBack Thread Tools Display Modes
  #1 (permalink)  
Old 05-28-2021, 03:41 PM
CC Member
Visit my Photo Gallery

 
Join Date: Apr 2021
Location: Rainbow valley, Az
Cobra Make, Engine: Lone star 351w /408cu.in.
Posts: 215
Neutral     
Default Welding on header on car, advice?

I found a crack on header easily accessible. Friend can Tig it. Any advice on preventing damage to car systems? For example, remove battery connections, unplug MSD connector to distributor. Other concerns? Thank you for your help. Oh yes, fire prevention steps will be taken. :-).
Reply With Quote
  #2 (permalink)  
Old 05-28-2021, 04:52 PM
cobrakiwi's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Apr 2006
Location: Charlottesville, va
Cobra Make, Engine: Coombe, Shelby Block 496
Posts: 1,182
Not Ranked     
Default

Put the welding ground cable directly on the header tube you will be welding.
eschaider and Bruce.huling like this.
Reply With Quote
  #3 (permalink)  
Old 05-29-2021, 09:30 AM
eschaider's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Feb 2006
Location: Gilroy, CA
Cobra Make, Engine: SPF 2291, Whipple Blown & Injected 4V ModMotor
Posts: 2,628
Not Ranked     
Default

+1^

You will contain the electrical energy to the location of the repair and minimize the potential for damage to in car electronics.


Ed
Gaz64 and Bruce.huling like this.
__________________


Help them do what they would have done if they had known what they could do.
Reply With Quote
  #4 (permalink)  
Old 05-30-2021, 06:22 AM
Jerry Clayton's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Jul 2005
Location: Bartlett, Ill
Cobra Make, Engine: Everett-Morrison LS1
Posts: 2,448
Not Ranked     
Default

Drill a small hole in the tube at both ends of the crack and then weld--------
eschaider, Gaz64 and Bruce.huling like this.
Reply With Quote
  #5 (permalink)  
Old 05-30-2021, 08:00 AM
patrickt's Avatar
Half-Ass Member
Visit my Photo Gallery

 
Join Date: Jun 2005
Cobra Make, Engine: ERA #732, 428FE (447 CID), TKO600, Solid Flat Tappet Cam, Tons of Aluminum
Posts: 21,889
Not Ranked     
Default

Quote:
Originally Posted by Jerry Clayton View Post
Drill a small hole in the tube at both ends of the crack and then weld--------
Uhhh, but won't all the electricity leak out on to the floor?
Reply With Quote
  #6 (permalink)  
Old 05-30-2021, 06:50 PM
eschaider's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Feb 2006
Location: Gilroy, CA
Cobra Make, Engine: SPF 2291, Whipple Blown & Injected 4V ModMotor
Posts: 2,628
Not Ranked     
Default

Quote:
Originally Posted by patrickt View Post
Uhhh, but won't all the electricity leak out on to the floor?
It is a risk Patrick but, I think what Jerry is doing with the holes is an old race car chassis builder technique that allows air to escape from a tube being welded that is closed on both ends without damaging the weld joint or the welder.

As the welding process proceeds, the air in the tube is being heated and absent the small air bleed holes the heated and expanding air in the tube would blow out a chunk of molten weld material from the weld joint.


Ed
__________________


Help them do what they would have done if they had known what they could do.
Reply With Quote
  #7 (permalink)  
Old 05-30-2021, 08:45 PM
Gaz64's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: May 2008
Location: Brisbane, QLD
Cobra Make, Engine:
Posts: 2,773
Not Ranked     
Default

You drill holes at the ends of the crack before welding the crack up, to remove the end of the crack, so the crack can't continue to crack in service, after the welding is done.
The crack is still evident under the weld if the ends of the crack aren't drilled.
Jerry Clayton likes this.
__________________
Gary

Gold Certified Holden Technician
Reply With Quote
  #8 (permalink)  
Old 05-30-2021, 09:18 PM
CC Member
Visit my Photo Gallery

 
Join Date: Apr 2021
Cobra Make, Engine:
Posts: 533
Not Ranked     
Default

Holes...sage advice.
Reply With Quote
  #9 (permalink)  
Old 05-31-2021, 12:41 AM
eschaider's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Feb 2006
Location: Gilroy, CA
Cobra Make, Engine: SPF 2291, Whipple Blown & Injected 4V ModMotor
Posts: 2,628
Not Ranked     
Default

Quote:
Originally Posted by Gaz64 View Post
You drill holes at the ends of the crack before welding the crack up, to remove the end of the crack, so the crack can't continue to crack in service, after the welding is done.
The crack is still evident under the weld if the ends of the crack aren't drilled.

You're right Gary. I was solving a problem that did not exist! It is definitely a way to prevent a continued spreading of the crack after welding.

Ed
__________________


Help them do what they would have done if they had known what they could do.
Reply With Quote
  #10 (permalink)  
Old 05-31-2021, 05:10 AM
t walgamuth's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Jan 2018
Location: Lafayette, IN
Cobra Make, Engine: Looking to buy
Posts: 1,295
Not Ranked     
Default

Quote:
Originally Posted by patrickt View Post
Uhhh, but won't all the electricity leak out on to the floor?
A classic!
cycleguy55 likes this.
__________________
Cobra loving, autocrossing Grandpa Architect.
Reply With Quote
  #11 (permalink)  
Old 05-31-2021, 07:12 AM
Jerry Clayton's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Jul 2005
Location: Bartlett, Ill
Cobra Make, Engine: Everett-Morrison LS1
Posts: 2,448
Not Ranked     
Default

WOW!!!!!!!!! The method of drilling hole at end of crack came from aircraft repair---not race car chassis repair----and its not just for tubing repair---as I sit here with my morning coffee at 80 years old thinking about all the things I've welded over the years---the worst thing in my memory is cutting some barbeb wire off the top of a fence so I cut weld up the inside panel on a combine out in the field-------and yes-it did catch on fire but there was a creek nearby so the farmer could pour some water on my pants leg until I could get out-----
Reply With Quote
  #12 (permalink)  
Old 05-31-2021, 10:31 AM
CC Member
Visit my Photo Gallery

 
Join Date: Apr 2021
Location: Rainbow valley, Az
Cobra Make, Engine: Lone star 351w /408cu.in.
Posts: 215
Not Ranked     
Default

Quote:
Originally Posted by Jerry Clayton View Post
WOW!!!!!!!!! The method of drilling hole at end of crack came from aircraft repair---not race car chassis repair----and its not just for tubing repair---as I sit here with my morning coffee at 80 years old thinking about all the things I've welded over the years---the worst thing in my memory is cutting some barbeb wire off the top of a fence so I cut weld up the inside panel on a combine out in the field-------and yes-it did catch on fire but there was a creek nearby so the farmer could pour some water on my pants leg until I could get out-----
You made me chuckle thinking of all the times I set myself on fire welding. Probably my favorite was welding a truss at the top of a 18 foot ladder doing an overhead weld. Darn spark went down my neck and into the top of my pants above the family jewels. Wish there had been phone video back then, I have to think for sure it was comical. I will drill a small termination hole at ends of the crack. I don’t TIG so I’m relying on a local whiz to do the deed. Ceramic coated stainless thin wall I believe. Worth a try. My car is a driver, not a show queen. Chicks dig scars, and I like welds. Go figure.
Blacklemming likes this.
Reply With Quote
  #13 (permalink)  
Old 05-31-2021, 12:40 PM
CC Member
Visit my Photo Gallery

 
Join Date: Apr 2021
Cobra Make, Engine:
Posts: 533
Not Ranked     
Default

A good weld is a thing of beauty, more of an art than a skill.
I took a couple classes at the Mesa Community College when I first retired but since I don't keep in practice, my welds don't look good until I'm about finished. The beginnings are reminiscent of pigeon poop. The grinder is my FRIEND!
Jerry Clayton and cycleguy55 like this.
Reply With Quote
  #14 (permalink)  
Old 05-31-2021, 02:49 PM
cycleguy55's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Feb 2014
Location: White City, SK
Cobra Make, Engine: West Coast, 460 CID
Posts: 2,844
Not Ranked     
Default

Quote:
Originally Posted by Bruce.huling View Post
You made me chuckle thinking of all the times I set myself on fire welding. Probably my favorite was welding a truss at the top of a 18 foot ladder doing an overhead weld. Darn spark went down my neck and into the top of my pants above the family jewels. Wish there had been phone video back then, I have to think for sure it was comical. I will drill a small termination hole at ends of the crack. I don’t TIG so I’m relying on a local whiz to do the deed. Ceramic coated stainless thin wall I believe. Worth a try. My car is a driver, not a show queen. Chicks dig scars, and I like welds. Go figure.
One of my high school buddies (back in the '70s) was taking a welding class and passed a lit cutting torch at least a foot above his pant leg. The problem was that he was wearing polyester pants without protection and melted them onto his thigh. Ouch.

On another note, a neighbour of mine was a welder by trade, mostly building tank trailers for highway usage. He had no love for welding overhead and said you basically had to let the spatter burn - if you tried to move it you just ended up with multiple burns.
eschaider and Bruce.huling like this.
__________________
Brian
Reply With Quote
  #15 (permalink)  
Old 05-31-2021, 07:13 PM
t walgamuth's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Jan 2018
Location: Lafayette, IN
Cobra Make, Engine: Looking to buy
Posts: 1,295
Not Ranked     
Default

my dad welded at Studebakers back in the late forties early fifties. He said if a drop of molten metal dropped off it would burn through his coverall entering and exiting. You just stood there and waited but if it hit your belt and got stopped by it being too thick to burn through you had to pull your belt and such away from your body so it would pass on down. If it got stuck you got a nasty burn.
__________________
Cobra loving, autocrossing Grandpa Architect.
Reply With Quote
  #16 (permalink)  
Old 06-01-2021, 08:26 PM
CC Member
Visit my Photo Gallery

 
Join Date: Apr 2021
Location: Rainbow valley, Az
Cobra Make, Engine: Lone star 351w /408cu.in.
Posts: 215
Not Ranked     
Default

Will disconnect the ignition box from distributor and ground lug from battery. Hope it doesn’t crap something out. Will keep the ground close to the weld zone. Also keep fire extinguisher handy.
Reply With Quote
  #17 (permalink)  
Old 06-01-2021, 09:48 PM
CC Member
Visit my Photo Gallery

 
Join Date: Apr 2021
Cobra Make, Engine:
Posts: 533
Not Ranked     
Default

Shouldn't be any flying slag with tig welding also a much smaller heat area.
Reply With Quote
  #18 (permalink)  
Old 06-02-2021, 06:36 AM
Jerry Clayton's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Jul 2005
Location: Bartlett, Ill
Cobra Make, Engine: Everett-Morrison LS1
Posts: 2,448
Not Ranked     
Default

As for the fire exinguisher----------also don't have anything parked outside the garage door---open door so IFFFFFFFFFFFFF you do start a FIREEEEEEEEEE you will be able to roll the car outside and down the drive away from building--------There have been previous occasions of house fires caused from cars being worked on------
eschaider and Bruce.huling like this.
Reply With Quote
  #19 (permalink)  
Old 06-02-2021, 11:14 AM
indianamoon's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Jul 2013
Location: South Bend, In
Cobra Make, Engine: B & B 289
Posts: 179
Not Ranked     
Default header weld.

Ground right on the pipe sounds like the way to go, and weld a bit at a time to keep the heat level down. Love them tigs.

Last edited by indianamoon; 06-02-2021 at 11:16 AM..
Reply With Quote
  #20 (permalink)  
Old 06-02-2021, 11:17 AM
CC Member
Visit my Photo Gallery

 
Join Date: Apr 2021
Location: Rainbow valley, Az
Cobra Make, Engine: Lone star 351w /408cu.in.
Posts: 215
Not Ranked     
Default

Quote:
Originally Posted by indianamoon View Post
Cast iron or steel? if cast iron, I always liked to preheat the area to be welded with an oxyacetylene torch, something that you probably shouldn't do with it on the car.....
Ceramic coated steel. Thin wall. Will take off car I decided as I can’t risk hurting something else in the electrics.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 08:42 AM.


Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: CC Policy