Roush Engine Warranty Exclusions.

[RodKnock]

Originally Posted by fordracing65

I know plenty of guys who use Fast efi or Big stuff 3 programs that would never touch a carb again for street use, it seems even the bad efi setups are better than the best carbs for street...

I think there are plenty here on ClubCobra who would argue that point.

If and when an EFI system is perfected, both installation, setup, tuning, a true plug and play system, I may be a buyer. But I haven't seen anything that folks haven't complained about.

And of course, there are some that are just downright fugly and I wouldn't buy it based on aesthetics.

[rodneym]

EFI in my Cobra?

It'll be installed right after the airbag.

[RodKnock]

Originally Posted by rodneym

EFI in my Cobra?

It'll be installed right after the airbag.

Passenger side, right? I thought you installed the driver's side already.

[fordracing65]

I think oil consumption is obvious different from car to car, build an aftermarket engine with any power adder, turbo, supercharge, or nitrious and use a carb and then use efi and then come talk to me, efi is far far superior, Kyroyer engines builds some of the finest efi engines around at a cost but they work like a dream, its a fact carbs work, efi works better, not these self learning systems I mean real tunable efi...

[rpatton3]

Originally Posted by RodKnock

Passenger side, right? I thought you installed the driver's side already.

My airbags block views of rear safety camera.

Russell

[jhv48]

Just got more great news:

It appears that after rebuilding the engine and needing new pistons due to the cracks on two of them, I also need to replace some of the valves and all of the guides as a few of the valves and all of the guides are showing more than normal wear. The builder remarked that this engine looked like it had been run without oil. Not on my watch, but who knows what happened before it was delivered to me. There goes another $1200 just for head work.

At least I am going to have the most expensive Roush 427 SRTW ever rebuilt.
Can't take away my bragging rights!

Now, can anyone tell me how to grind off the ROUSH name from my air cleaner lid? I've already replaced the valve covers with generic Ford covers.

[Varmit]

Originally Posted by jhv48

Just got more great news:

It appears that after rebuilding the engine and needing new pistons due to the cracks on two of them, I also need to replace some of the valves and all of the guides as a few of the valves and all of the guides are showing more than normal wear. The builder remarked that this engine looked like it had been run without oil. Not on my watch, but who knows what happened before it was delivered to me. There goes another $1200 just for head work.

At least I am going to have the most expensive Roush 427 SRTW ever rebuilt.
Can't take away my bragging rights!

Now, can anyone tell me how to grind off the ROUSH name from my air cleaner lid? I've already replaced the valve covers with generic Ford covers.

Damn Jim, what the hell happened to your engine!!!!!!!

[jhv48]

I wish I knew. When the heads were removed, there was no cross hatch visible in any of the cylinders. Should have been visible with 13,000 miles. There were even a couple of tiny gouges in two of the cylinder walls. A couple of lifters were showing abnormal wear. The heads are being rebuilt due to wear. Either this engine was just a POS from the get go or maybe it was accidentally run without oil before I received the car. Who knows?

All I know is the rebuild is costing more than the original cost of the engine. I guess I just expected more. Should have gone with another engine builder. Why Roush feels they have to build an engine with looser tolerances is beyond me. If I had read their exclusion paragraph, I would have passed and bought another engine.

Oh we'll, it's only time and money. But it's my f--kin time and money.