| blykins |
11-15-2017 04:09 PM |
Yes I did.
|
| stroked windsor |
11-15-2017 04:10 PM |
ok. wasn't sure it was working.. thanks.. def looking onto the air gap for my car..
|
| blykins |
11-15-2017 04:11 PM |
What's your cam specs and what heads are you running?
|
| stroked windsor |
11-15-2017 04:16 PM |
AFR 205 heads un ported HR cam 230-236-513-526-110. had a bigger roller 240 248 but wanted to bring down the torque curb. interesting that the small cam was just as good as the bigger cam.. just lost a few top end hp.. both had 535 ft lbs but the smaller cam came in much lower..
|
| blykins |
11-15-2017 04:18 PM |
If you'd be willing to swap cams again, I could have one ground for you that would keep the same peak hp but would give you more mid range and more torque.
|
| stroked windsor |
11-15-2017 04:22 PM |
be my 3rd cam change.. I am running a 8" converter on my car.. I think 4000 stall.. my motor starts pulling over 500 ft lbs@3700 with the small roller.. up to 4900 peak.. 535..
|
| blykins |
11-15-2017 04:22 PM |
Calling it a night....
If you want to chat more about your options, shoot me an email and I'll get back to you in the morning.
brent@lykinsmotorsports.com |
| blykins |
11-15-2017 04:23 PM |
You have too much converter for one thing and a new cam would help.......shoot me an email.
|
| jhv48 |
11-16-2017 08:53 AM |
Just saw this post was active again and thought I’d give a three year review on this 438W Brent built for me.
It’s fu—in awesome. Great street manners and pulls like a freight train when asked too. I have 200 treadwear tires and live where it’s nice and warm and can easily break em loose in third gear if I’m not careful. Idle is lumpy and has been a pleasure to drive for the past three years.
Thanks, Brent. Great build.
|
| jhv48 |
11-19-2025 07:07 PM |
Here’s an 11 year, 35,000 mile update.
Still runs great. No problems at all. Still can make the wife pee her pants.
|
| Grubby |
11-20-2025 09:23 AM |
Brent is a good guy and skilled engine builder.
17,000 on my FE build. Met my requirements and not a drip of oil.
John
|
| Grubby |
11-20-2025 09:25 AM |
Brent is a good guy and skilled engine builder.
17,000 on my FE build. Met my requirements and not a drip of oil.
John
|
| All times are GMT -7. The time now is 01:15 AM. |
|
Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link:
