Details, details, details-original looking details
 

After writing the post below in another thread, it got the wheels turning as to what the detail differences are for SPS0034 and CSX 8036 that was recently on BAT. Even though it is currently listed for sale (as is ERA2080), I clearly need something to tinker with. With that said, I need assistance in finding the correct part numbers for the following:

Stock 3 wire "long" alternator harness to reach voltage regulator(currently 1 wire) on firewall
Stock alternator
Pulley and bracket set for front engine accessories
AC logo 2 ear knock offs (I have this somewhere, but cannot find it at the moment)
Early style Cobra badges (nose and trunk)
Early style dash switches and correct ignition switch
Lucas headlights that 8036 has installed
Correct Stewart Warner voltage gauge (his is the same as mine, but I know there has to be a "vintage looking" alternative
Correct "vintage look" clock
Bolt on AC pedals (I have little fabricating tools these days)

I'm certain someone before me has done this, and has a list of any and all parts and sources for the above, so any assistance would be greatly appreciated.

Sincerely,

Bill S.

Bill,

I have a 62 Galaxie clock available, needs the bezel replated and the clock rebuilt (it was but it got flooded...)

I can put you on several of the parts you need.

You've got my email, send me the details on the clock and I am assuming the dash switches and such.

Any leads on the alternator harness, Bueller, Bueller, anybody, anybody :LOL:

As for the AC 2 ear knock offs, think I found them HERE , part numbers KCK293LH/KCK292RH just need to confirm the thread size are correct for the SPF 289 roadster and wire wheel combination.

Let's see if we can document for future builders as well here.




Bill S.

The AC repop spinners are also available here: https://www.holden.co.uk/p/ac_ace_le..._wheel_spinner

They seem to sell out quickly.

The repops have feathers on the arrows while the originals do not.

There were a few other things on 8036 that were not original that you may have noted:

- The wipers parked on the wrong side
- The central mirror was a repop and not mounted as original. More original Lucas mirrors are available
- No windscreen washer jets
- Rear bumper is from a 427 not a 289. Too wide and sticks out too far. Same issue with SPF Mark II's
- Modern wiper motor instead of a Lucas DR3
- No trunk accessories (tool kit, jack, jack handles and holder, bow holder clip, ...)
- No date plate on the McCord expansion tank

Not an exhaustive list but perhaps gives you something to "tinker with".

The correct alternator pulley is going to be an issue and will take some time to find. I’ve had to turn down two restorers recently that contacted me, each looking for one.
Larry

I'm not looking for 100% concourse correct, I'm looking for form, function, and of course the correct "look". Rick just showed me his set up with a 1 wire alternator that looks close enough to correct for me, so I'm open to quality alternatives, as I do drove everything I own, whenever I can.


Bill S.

I understand! Concours would be even much harder as correct alternator cases are more rare then hens teeth! Die cast, not sand cast and now 50+ years later, lots of those have been bead blasted ruining the original finish! I’d look for an old alternator and use the smaller press-on pulley. I have one of those I’ll give you if you choose that route.
Larry

Bill, NOT a "one-wire" alternator, it is the correct Ford 1G as used on 63-64 T-Birds and Lincolns.

Bill, you know my feelings on the subject.

I'd defintely go 100% concours correct on your SPF. :LOL:

Gotcha :JEKYLHYDE

I hear yours is covered in concourse correct dust from lack of use. :p


Bill S.

At this point, it's technical classification is considered "barn find." :D

If you look thru the documents included with the owners manual included with your car the fix for the wipers parked on the wrong side is included in the information. Fix is valid for SPF MK II’s and CSX 7000/8000 cars. Also works on SPF MKIII’s and CSX6000/8000 cars.
Blas

I’ve got several of the parts, including the alternator pulley and I believe I have the case also. I also reproduce the correct alternator mounting bracket casting (in steel not aluminum) with the correct logo and adjusting arm. I also have a set of the correct body KONI shock absorbers, intake manifold and cast aluminum oil pan. NOS water pump mounted fan blade……

How about an original 1964 48 IDA Weber system????

By the way, contact me as I have some suspension fixes you will want to do before driving that car.

Very early COBRA aluminum manifold....

Did any 289 Cobras come with a voltage gauge?

Cheers,
Glen

The original Shelby AC Cobra badge was: S1CS-A. Dan can tell you all about those. There are knock off, that very from great, to terrible! Here is the story of the correct flightless arrow, near and off side spinners, scroll down a ways. https://aceac.weebly.com/ac-ace-wheels--spinners.html Cheers, Dennis

Bill, this may help some, not complete, maybe others can feel in the blanks! Cheers, Dennis Mk1 and II

Up to chassis CSX 2054 - 'Shelby AC Cobra' motifs front and rear Ed Hugus 260 Cobras, Shelby AC Cobra Badges, nose and boot, AC medallion nose, AC script badge. boot. Tasca 260 Cobra Shelby AC Cobra badge nose, AC script on boot.

CSX 2055 to CSX 2132 - the 'flat headed' Cobra emblem front and rear

CSX 2132 onwards - the later Cobra emblem front and rear

Early CS, COB/COX chassis cars - 'flat headed' Cobra emblem on front, AC badge on rear.

Later COB/COX chassis cars - later Cobra emblem on front, AC script on rear. Hugus Ford in PA or Tasca in Rhode Island 1962 Galaxie Clock C2AZ-15A000-A ELECTRIC CLOCK KIT 2160, when side-vents were added, and 2200, when Stewart Warner instruments came into play, as it appears to have the early Smiths gauges CSX2071 - CSX2200 built using Ford generators jack Shelley 12DL 38 Grease Gun Tecalemit GB 2800 AMCO #5234 Luggage Rack

Why do I bother, to make the nicely spaced rows, only to have them jumble together? Cheers, Dennis