Club Cobra Keith Craft Racing  

Go Back   Club Cobra > Manufacturers, Engine Builders, tools, and parts. > Antique & Collectibles

Keith Craft Racing
Nevada Classics
Main Menu
Module Jump:
Nevada Classics
Nevada Classics
MMG Superformance
Advertise at CC
Banner Ad Rates
MMG Superformance
Keith Craft Racing
March 2024
S M T W T F S
          1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
31            
  #1 (permalink)  
Old 08-29-2007, 04:43 AM
CC Member
Visit my Photo Gallery

 
Join Date: Sep 2006
Cobra Make, Engine:
Posts: 242
Not Ranked     
Default Left front tire rubbing

Hey guys: Still haveing problems with my left front tire rubbing. I was thinking on lowering my rear end to see if that would lift up the front. Even though i really like the way it sits right now with the rear end high. What level did you all set yours up at? I have tightened up the left spring using the nut on the bottom of the shock. The left side is like 5 threads higher then the right side. I dont like that at all. I loosed the lower control arm but have not touched the upper yet.

The adjustable knobs on the bottom. How do they work? When you are facing the knob, what happens when you turn it counter clock wise and clock wise.

Automan
Reply With Quote
  #2 (permalink)  
Old 08-30-2007, 08:54 AM
PNJSNAK's Avatar
Club Cobra Member
Visit my Photo Gallery

 
Join Date: Nov 2000
Location: Macedonia, OH
Cobra Make, Engine: A&C 427S/C, 351W, T5
Posts: 513
Not Ranked     
Default

Automan:
I could not get the correct ride height on my car at first.
I spoke with Joe T and he sent me aluminum spacers that go above the springs under the frameand they pilot the ID of the spring to keep them in place.
I was then able to adjust the bottom of the shock to get the right height
__________________
OhioCobraClub.com
Reply With Quote
  #3 (permalink)  
Old 08-30-2007, 08:57 AM
PNJSNAK's Avatar
Club Cobra Member
Visit my Photo Gallery

 
Join Date: Nov 2000
Location: Macedonia, OH
Cobra Make, Engine: A&C 427S/C, 351W, T5
Posts: 513
Not Ranked     
Default

Automan:
Look at my gallery at the pic of the engine area. Pan to the right and you can see the spacer above the spring on the drivers side.
Jim
__________________
OhioCobraClub.com
Reply With Quote
  #4 (permalink)  
Old 08-31-2007, 04:21 AM
CC Member
Visit my Photo Gallery

 
Join Date: Sep 2006
Cobra Make, Engine:
Posts: 242
Not Ranked     
Default

Thanks Jim, i will call Joe today and see if he could send me some spacers too. I see that your car's rear end sits lower then mine. Can you tell me which holes you have your rear coil overs mount to on that bracket. Just tell me for example that your lowest bolt is going through the 2 hole up.

Thanks
Automan
Reply With Quote
  #5 (permalink)  
Old 08-31-2007, 04:23 AM
CC Member
Visit my Photo Gallery

 
Join Date: Sep 2006
Cobra Make, Engine:
Posts: 242
Not Ranked     
Default

Also, So if i tighten that spring, it will raise the car. Man, the passenger side is at its lowest thread while the driverside is at least 5 thread up.
Reply With Quote
  #6 (permalink)  
Old 08-31-2007, 07:23 AM
CC Member
Visit my Photo Gallery

 
Join Date: Dec 2004
Location: Dansville, NY
Cobra Make, Engine: A&C , 466 Ford, 5speed Tremec
Posts: 92
Not Ranked     
Default Tire Rubbing ?

Automan,
This may sound like a dumb question, but did you have the front end alligned yet? If not, that could be the problem. When I had mine done they had to order extra shims to bring the camber of the wheels into place. I would say between 1/2 and 3/4 of an inch of shims were used and if the caster is to far forward or back the tires could hit the front or rear of the fender well in a tight turn. Sam
Reply With Quote
  #7 (permalink)  
Old 08-31-2007, 09:28 AM
MaSnaka's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Feb 2006
Location: Thousand Oaks, CA
Cobra Make, Engine: Classic Roadster
Posts: 1,359
Not Ranked     
Default

I am not familiar wit A&C, but many cars use the Mustang II front suspension. Does yours? My front would rub in moderate-hard cornering and especially on bumps or dips. I replaced the stock front a arms and used coil over springs and shocks. I found the original springs were way under rated for the front end. I now have 500# springs which carry the front end nicely.

Is it possible your springs are too light? BB with Small block spring rating?

You could swap (r-l and l-r) your coil overs to the other side and see if the problem remains or migrates to the passenger side.

Possible your anti sway bar needs some adjustment.

Do you need a different backset on your wheels?

I don't know for sure just throwing ideas your way that might help.

Good Luck!!
John
Reply With Quote
  #8 (permalink)  
Old 08-31-2007, 01:32 PM
PNJSNAK's Avatar
Club Cobra Member
Visit my Photo Gallery

 
Join Date: Nov 2000
Location: Macedonia, OH
Cobra Make, Engine: A&C 427S/C, 351W, T5
Posts: 513
Not Ranked     
Default

Automan:

On my rear coil over shock setup. There is an L shapped bracket that has
(2) bolts bolting it to the bracket on the rear axle tube.
The bolt on the top is located in the second hole from the top of the bracket.
I can't tell how many holes up the lower bolt is. But when I look at it I see a single hole exposed below the bottom of the bracket.
Also, on the adjustable nut on the bottom of the shock there is about 3/16" of thread exposed.
Hope this helps.
Jim
__________________
OhioCobraClub.com
Reply With Quote
Reply

Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 02:34 AM.


Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: CC Policy
Links monetized by VigLink