Club Cobra GasN Exhaust  

Go Back   Club Cobra > General Discussion > Consumer Watch

Nevada Classics
MMG Superformance
Main Menu
Module Jump:
Nevada Classics
Nevada Classics
Keith Craft Racing
Advertise at CC
Banner Ad Rates
MMG Superformance
Keith Craft Racing
March 2024
S M T W T F S
          1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
31            
  #1 (permalink)  
Old 03-24-2002, 05:47 PM
CC Member
Visit my Photo Gallery

 
Join Date: Aug 2001
Location: Brandon, Fl,
Posts: 160
Not Ranked     
Default Windshield tensor bar?

Does anyone have any experience with using a tensor bar? I picked up some substantial rock chips on my windshield recently, and the shield finally expressed a crack between two of the chip points today. I am going to replace the windshield glass this week. I have not had any vibration problems up to this point, and I have not seen any tensor bars on members cars. However, I noticed that Finish Line shows a windshield tensor bar in it's catalog which is not very expensive. I was just trying to find out if this is an ounce of prevention against future cracking from vibration. Obviously, it won't prevent chips or cracks from rocks flying up from "the road devils". So what's the application for the tensor, in problem solving? Thanks.

FIAFRED
Reply With Quote
  #2 (permalink)  
Old 03-24-2002, 06:37 PM
CobraDan's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Jan 2001
Location: Cape Coral, FL
Cobra Make, Engine: 2009 Solbra
Posts: 3,861
Not Ranked     
Default

The main reason for the tension bar is to support the windshield if you are running with a soft or hardtop in place. It can't hurt to have one even if you never run with a top.
Dan
Reply With Quote
  #3 (permalink)  
Old 03-25-2002, 12:22 PM
CC Member
Visit my Photo Gallery

 
Join Date: Mar 2002
Location: Dawsonville, Ga
Cobra Make, Engine: FFR4252CP,5.0,e-cam,performer RPMs,stacks,3-link,torque thrust "D"s
Posts: 42
Not Ranked     
Default

Some of the guys on the other forums have attempted to mount the tensioner and found that the screws in the bottom were too long and screwed into the glass cracking it!. Be very careful! Bob
__________________
Re-retired! Finishing up the coupe and BB Roadster
Reply With Quote
  #4 (permalink)  
Old 03-25-2002, 02:10 PM
CC Member
Visit my Photo Gallery

 
Join Date: Sep 2001
Location: Mars, Pa
Cobra Make, Engine: Superformance #1287 -- Shelby Aluminium 504ci FE SOLD 2007..--------Superformance #2305 Ford FE 482ci Sideoiler Presently
Posts: 70
Not Ranked     
Default

I just picked up my new Superformance 2 weeks ago It has the tension bar on it...
__________________
Steve McD
Reply With Quote
  #5 (permalink)  
Old 03-25-2002, 03:19 PM
Snakecharmer's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Dec 1999
Location: Cedar Park, Tx
Cobra Make, Engine: Empty handed for the moment
Posts: 389
Send a message via AIM to Snakecharmer
Not Ranked     
Default

I believe that it is also used to support the windshield at high speed.

I've bought quite a bit of stuff (and more to come!) from the Finish Line. I can't say enough about Paula and Enzo. Top Notch company and top notch people. As honest and fun loving as they come If you have ANY questions, they'd be happy to answer them for you. Good luck.

Charmer
Reply With Quote
  #6 (permalink)  
Old 03-25-2002, 04:15 PM
CC Member
Visit my Photo Gallery

 
Join Date: Jun 2001
Location: Washington DC Metro (Virginia), VA
Cobra Make, Engine: Classic Roadsters, Tweaked 351W, T-5Z, CRII Tech Support Team.
Posts: 1,895
Not Ranked     
Default

Can one of you folks tell me what a tension bar is, where it mounts, and what it does? I have a soft top, and at 70 MPH and up, the top does put a lot of stress on the windshield frame.
Reply With Quote
  #7 (permalink)  
Old 03-25-2002, 04:26 PM
CC Member
Visit my Photo Gallery

 
Join Date: Jan 2002
Posts: 19
Not Ranked     
Default

My old MGB had tension bar I never gave a thouhgt to putting one on my cr I bet it would help when you have a top
Reply With Quote
  #8 (permalink)  
Old 03-25-2002, 04:27 PM
Dwight's Avatar
Senior Club Cobra Member
Visit my Photo Gallery

 
Join Date: May 2001
Location: Florence, AL
Cobra Make, Engine: RCR GT 40 & 1966 Fairlane 390 5 speed
Posts: 4,511
Not Ranked     
Smile Tension Bar

I bought a tension bar from Finish Line. What size and length screws do I need to mount the tension bar to the windshield?


GREAT people Paula and Enzo!!!!!!!!!
__________________
''Life's tough.....it's even tougher if you're stupid.'' ~ John Wayne
"Happiness Is A Belt-Fed Weapon"
life's goal should be; "to be smarter than inanimate objects"
Reply With Quote
  #9 (permalink)  
Old 03-31-2002, 05:20 AM
CC Member
Visit my Photo Gallery

 
Join Date: Jun 2000
Location: Yardley, PA 19067,
Posts: 175
Not Ranked     
Default

The tensor bar is made to insure that the stress on the windshield frame is spread evenly. If you are moving at speed with a top on the car, there is a lot of stress pulling at single point which can separate the frame from the glass. The tensor bar spreads that stress to the entire frame. SPF first epoxied the glass to the frame as a fix but this is a problem if you have to replace the windshield. I understand that several British sports cars from the 60's had them a well.

Jack Z.
Reply With Quote
  #10 (permalink)  
Old 03-31-2002, 09:13 AM
CC Member
Visit my Photo Gallery

 
Join Date: Dec 2000
Location: so calif,
Posts: 174
Not Ranked     
Default

Finish Line folks ARE great for parts.

BTW...aside from rocks and people pulling back on the windshield, I wonder if the next cause of stressed $windshields are excessive flex on the actual car-frame.

I really worry about this every time I jack the car up !

scratch
Reply With Quote
  #11 (permalink)  
Old 03-31-2002, 09:47 AM
Dwight's Avatar
Senior Club Cobra Member
Visit my Photo Gallery

 
Join Date: May 2001
Location: Florence, AL
Cobra Make, Engine: RCR GT 40 & 1966 Fairlane 390 5 speed
Posts: 4,511
Not Ranked     
Smile FRAME FLEX

I DO NOT THINK THAT MY FRAME FLEX WHEN I PICK IT UP. IT'S TO WELL BUILD! A STRONG AND WELL BUILD COWLING BAR SHOULD PREVENT FLEXING OF THE WINDSHIELD.
__________________
''Life's tough.....it's even tougher if you're stupid.'' ~ John Wayne
"Happiness Is A Belt-Fed Weapon"
life's goal should be; "to be smarter than inanimate objects"
Reply With Quote
  #12 (permalink)  
Old 04-04-2002, 09:42 AM
rdorman's Avatar
Renegade Nuns on Wheels
Visit my Photo Gallery

 
Join Date: Aug 2001
Location: columbus, Oh
Cobra Make, Engine: Unique 427 roadster with 351C-4B
Posts: 5,129
Not Ranked     
Default 2000 miles soft top on all the way!

When I was driving my cobra back from Phoenix to Columbus OH a little less that half way the soft top had pulled the frame completely off the glass in the center of the windscreen! Sure the soft top parts warned against going over 60 with the top up, but do I listen, nope. I stopped at a ACE hardware store and made a interium tensioner and proceeded back down the road continuing my high speed misbehavior. No problems after that.

I have since received and installed the tensioner from the finish line. Nice piece and works great. Two things to second here:
- ANY time you screew into the frame be sure that the screws are so long as to contact the glass!
- ALWAYS use a tensioner with the top. 'ALWAYS' as is why not? Sure as heck won't hurt!

Happy motoring

See you at DVSF II!
Reply With Quote
  #13 (permalink)  
Old 06-25-2014, 04:47 PM
davids2toys's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Dec 2006
Location: Southbury, ct
Cobra Make, Engine: ERA, 428, 4 speed Toploader, Jag rear, Red with White stripes
Posts: 922
Not Ranked     
Default

Found this thread in a search.
I purchased this bar from Finishline and can't figure out how to install it. It came with no instructions at all. I called them and sent an email but they were no help at all except to tell me to go to the forums. I bought this for looks only, I just really like the look, I don't even have a top...LOL
My car already has the brace at the bottom of the windshield and I assume it gets used in conjunction with the brace already there. The bracket that came with the rod is at a 90 deg angle. If i was to put this on top of the present brace at the bottom of the windshield, I think it would be almost impossible to put the screws back in.
Does anybody know how to properly install this support rod. Thanks in advance for any help I can get
Dave
__________________
ERA#698 428, 4 speed Toploader, 3:31 Jag rear
Reply With Quote
  #14 (permalink)  
Old 06-26-2014, 06:15 AM
Dwight's Avatar
Senior Club Cobra Member
Visit my Photo Gallery

 
Join Date: May 2001
Location: Florence, AL
Cobra Make, Engine: RCR GT 40 & 1966 Fairlane 390 5 speed
Posts: 4,511
Not Ranked     
Smile

12 year old thread, great.
I now have 41,000 miles on my car and I think the windshield flexs a lot at speed.

are you talking about the rod that goes in the center of the windshield? Top to bottom?
If so it has a hook on one end and threaded on the other. The hood installs on the top of the windshield in the slot. The threaded end goes thru the plate at the bottom. I removed my windshield to install the plate to the windshield. I think the screws are 4x40.
The holes should be in the windshield frame. Same ones used to mount an L-bracket to hold the windshield to the body.
This rod is used to keep the windshield frame from spreading apart at speed and dropping the glass out.
I hope this helps

Dwight
__________________
''Life's tough.....it's even tougher if you're stupid.'' ~ John Wayne
"Happiness Is A Belt-Fed Weapon"
life's goal should be; "to be smarter than inanimate objects"
Reply With Quote
  #15 (permalink)  
Old 06-26-2014, 06:21 AM
Dwight's Avatar
Senior Club Cobra Member
Visit my Photo Gallery

 
Join Date: May 2001
Location: Florence, AL
Cobra Make, Engine: RCR GT 40 & 1966 Fairlane 390 5 speed
Posts: 4,511
Not Ranked     
Smile

here is a thread with pictures.

Windshield center bracket or not?
__________________
''Life's tough.....it's even tougher if you're stupid.'' ~ John Wayne
"Happiness Is A Belt-Fed Weapon"
life's goal should be; "to be smarter than inanimate objects"
Reply With Quote
  #16 (permalink)  
Old 06-26-2014, 02:56 PM
davids2toys's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Dec 2006
Location: Southbury, ct
Cobra Make, Engine: ERA, 428, 4 speed Toploader, Jag rear, Red with White stripes
Posts: 922
Not Ranked     
Default

Thanks Dwight,
Yes, 12 year old thread found in a search for info!
I have seen that thread,. i am trying to install it with the windshield in the car. i have the L bracket at the base of the windshield already on the car. Is it used in conjunction with the L bracket and is it possible to install with the windshield still installed in the car?
Dave
__________________
ERA#698 428, 4 speed Toploader, 3:31 Jag rear
Reply With Quote
  #17 (permalink)  
Old 06-26-2014, 03:38 PM
Cashburn's Avatar
Backdraft Racing Dealer
Visit my Photo Gallery
Lifetime Contributor
 
Join Date: Dec 2004
Location: North Haven, CT
Cobra Make, Engine: Backdraft Racing
Posts: 5,115
Not Ranked     
Default

Get the bracket FFR uses/sells it does not go into the dash.
__________________
IT'S NOT REAL. IT'S UNREAL.
VINTAGE MOTORSPORTS
888.427.1965 | www.vintagemotorsports.com
Reply With Quote
  #18 (permalink)  
Old 06-26-2014, 09:09 PM
davids2toys's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Dec 2006
Location: Southbury, ct
Cobra Make, Engine: ERA, 428, 4 speed Toploader, Jag rear, Red with White stripes
Posts: 922
Not Ranked     
Default

I wonder what is anchoring it then? Also I already have the two holes in the dash from the present fasteners, I will go their site and check it out.
Well I went to their site and did multiple searches, I cant find it.
Can anybody post a pic of theirs installed? I will have to call them.
Dave
__________________
ERA#698 428, 4 speed Toploader, 3:31 Jag rear
Reply With Quote
  #19 (permalink)  
Old 06-27-2014, 03:41 AM
cobrajeff's Avatar
Senior Club Cobra Member
Visit my Photo Gallery

 
Join Date: Dec 1999
Location: Edgewater, FL
Cobra Make, Engine: ERA FIA, BOSS 351C/Webers
Posts: 1,304
Not Ranked     
Default Windshield Tensor

I made my own, patterned after the one in CSX2259. You have to be extremely careful about the length of the mounting screws that go into the windshield frame - 1mm too long, and your windshield is toast.



Took several trial and error attempts to get the angle just right for the rake of my laid-back windshield. I had to put slotted holes in the base of the bracket to be able to tighten the lower screws to the windshield frame.

regards,

Jeff
__________________
CobraJeff
ERA P 202
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 08:04 AM.


Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: CC Policy
Links monetized by VigLink