SUPPORT OUR SPONSOR

Go Back   Club Cobra > Club Cobra Tech Areas > Shop Talk

Welcome to Club Cobra!  The World's largest non biased Shelby Cobra related site!

  •  » Representation from nearly all Cobra/Daytona/GT40 manufacturers
  •  » Help from all over the world for your questions
  •  » Build logs for you and all members
  •  » Blogs
  •  » Image Gallery
  •  » Many thousands of members and nearly 1 million posts! 

YES! I want to register an account for free right now!  p.s.: For registered members this ad will NOT show

MMG Superformance
Nevada Classics
MMG Superformance
Main Menu
Nevada Classics
Nevada Classics
MMG Superformance
Advertise at CC
Banner Ad Rates
MMG Superformance
MMG Superformance
MMG Superformance
March 2024
S M T W T F S
          1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
31            
  #1 (permalink)  
Old 02-24-2002, 05:22 PM
CC Member
Visit my Photo Gallery

 
Join Date: Apr 2000
Location: Channel Islands Harbor (Oxnard, CA), ca
Cobra Make, Engine: Classic Roadster, 351Cleveland
Posts: 172
Not Ranked     
Angry Help - 351C Rear Seal Blown

Went out to bruch with Spotterjoe and when I came back the rear crank seal was blown. Oil all over the bottom side of the car and leaking from the bottom of the clutch cover.
Can the rear seal in a 351C be replaced without completely pulling the crank or having to pull the engine??

John W
Reply With Quote
  #2 (permalink)  
Old 02-24-2002, 05:55 PM
CC Member
Visit my Photo Gallery

 
Join Date: Jan 2002
Location: west viginia,
Posts: 17
Send a message via ICQ to COBRAMIKE427
Not Ranked     
Default

Yes it can,pull the flywheel cover,oilpan,rear main cap,rotate top half of seal out.If old seal is rope replace with neoprene unit from felpro. To reinstall apply permatex#3D to the back of the seal and rotate it back in leaving 1/8"of seal sticking out and making sure the seal is installed in the right direction. Then replace seal half in main cap leaving 1/8"of one end sticking out oppisite of the half in the block. Then apply sealer to the face of the cap only from the seal to the rear of the block then reinstall cap then torque cap bolts 95-105ft#
Reply With Quote
  #3 (permalink)  
Old 02-24-2002, 07:54 PM
CC Member
Visit my Photo Gallery

 
Join Date: Dec 2000
Location: Clearville,PA,
Posts: 44
Not Ranked     
Default

If it has the rope type seal in it and you replace it with the rubber seal, check the cap to see if the small pointy "nail" is still there. Its function was to keep the rope seal from rotating. If you use the rubber seal, remove the nail with a small punch and put a little silicon in the hole thats left to plug it.

Dave
Reply With Quote
  #4 (permalink)  
Old 02-24-2002, 07:58 PM
CC Member
Visit my Photo Gallery

 
Join Date: Apr 2000
Location: Channel Islands Harbor (Oxnard, CA), ca
Cobra Make, Engine: Classic Roadster, 351Cleveland
Posts: 172
Not Ranked     
Question Ok - Question

Cobramike427
Boy did you improve my disposition.
I understand all your instructions - nice detailed job - already printed out.
A couple of questions:
1. I assume that you can grab one end of the rope seal with needle nose pliers and pull on the seal and rotate the crank at the same time - correct??
2. What if its not a rope seal or did all the 351C's have the rope seal and if not, do you use the same technique and the same or different seal??

Dave Posted while I was writing this, is the nail in the cap??

John W
I see light at the end of the tunnel
Reply With Quote
  #5 (permalink)  
Old 02-24-2002, 08:18 PM
CC Member
Visit my Photo Gallery

 
Join Date: Dec 2000
Location: Clearville,PA,
Posts: 44
Not Ranked     
Default

Yes, the nail is in the cap with the point sticking into the groove the rope seal fit in. It will be obvious which you have when you get it apart. The rope is like an O ring cut in half with half in the block and half in the cap. It will be mashed flat where it rides against the crank flange and makes its seal.

The rubber type seal looks like a conventional lip type seal that is again, cut in half, with half in the cap and half in the block. The idea of rotating the split joint to not line up with the cap/block mating surface is to reduce the possibility of the seal leaking where the two ends butt.

The rubber type lip seal is probably the better (and newer) design of the two. It's lip functions just like any other conventional oil seal. It is supposed to reduce rotating friction caused by the rope type.

Don't know how easy it will be to rotate the old seal out and the new seal in the block out while the crank is still in. The cap is a no brainer. Certainly worth a try. Good luck!

Dave
Reply With Quote
  #6 (permalink)  
Old 02-24-2002, 08:30 PM
tim tim is offline
CC Member
Visit my Photo Gallery

 
Join Date: Jan 2000
Location: Senoia, GA
Cobra Make, Engine: Everett-Morrison, Boss 351 w/ TKO 5 speed, 94 vette suspension
Posts: 76
Not Ranked     
Default

For what it's worth; I haven't ever seen a rope type rear main seal in a Ford, at least one built from the early 60's to the present. My 351C came with a rubber 2 piece seal. You may have to loosen all the main caps to allow the crank to drop down a little so that you can remove and replace the seal.
Tim
Reply With Quote
  #7 (permalink)  
Old 02-24-2002, 10:48 PM
Bill E's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Mar 1999
Location: Redding, CA
Cobra Make, Engine: Cobra Maker
Posts: 722
Send a message via AIM to Bill E Send a message via Yahoo to Bill E
Not Ranked     
Default

Tim there is a weir in the rubber seal if you use a small wooden dal for a punch tap one end of the seal till you can get a hold of the other end. Then you should have no problems from there.
__________________
Bill Emerson
Reply With Quote
  #8 (permalink)  
Old 02-25-2002, 01:37 PM
CC Member
Visit my Photo Gallery

 
Join Date: Jul 1999
Location: birmingham, alabama,
Posts: 63
Not Ranked     
Default Rope vs Rubber

If you have a rope crank, the rubber seal will weep a little. The rope crank has small slashes(couldn't think of any other way to describe it) that help drive any seepage back into the block.....There is a rope crank seal installation kit that you can buy at NAPA....I have never replaced mine but I do know that I have a rubber seal and a rope crank...It will leak a smal amount ....enough to annoy the heck out of you but not enough to get on your back and replace it....good luck!!!
Reply With Quote
  #9 (permalink)  
Old 02-25-2002, 10:05 PM
CC Member
Visit my Photo Gallery

 
Join Date: Apr 2000
Location: Channel Islands Harbor (Oxnard, CA), ca
Cobra Make, Engine: Classic Roadster, 351Cleveland
Posts: 172
Not Ranked     
Post Thanks guys

Wound up with a fairly large amount of oil on a drip pan. I don't usually have a drip pan because the garage is carpeted. Drove the car about 6 miles to C & S which is a very good local shop for Cobras and put it up on the rack. Now it has only 1 small drip -- go figure. A fair amout of oil is around the rear of the pan, front bell housing cover and some splattered sideways on the frame.
Decided to replace the seal regardless and obviously the pan seal. Topside and front of the engine is dry - its not the oil pressure sensor or intake manifold.
Took Tuesday off and we will see!!!
Decided to let C & S do it instead of lying on my back trying to change it out. After all the help, I could have done it myself, just didn't feel like it. This way I will get the car back the same day.
Thanks everyone for your response, I really appreciate it.

John W.
Reply With Quote
  #10 (permalink)  
Old 06-13-2014, 09:10 AM
CC Member
Visit my Photo Gallery

 
Join Date: Jun 2014
Cobra Make, Engine:
Posts: 2
Not Ranked     
Default

Nothing like dredging up an old post, but this is where I am, and it's the best post I found on the subject so far. (1973 Coupe, 351C 2V, FMX trans, sat in AZ heat for 4 years - dry upper seal?)

Engine in the car, pan is off, Rear main cap is off, all main caps are loose. Removing a rope seal, but can't actually grab it with a Sneaky Pete, but have managed to remove a lot of the seal bit by bit using it. I doubt I'll get much more out of it as it is, so I'm looking for options. This morning, because I am procrastinating dropping the crank or removing the transmission, I'm trying cooling the crank to see if the metal will "shrink" enough to loosen its grip (highly unlikely I know, and it's only 8 am, and it will be 107 today, and there are worse things than sitting in the shade under the car with ice melting nearby.)

Anyway, is it possible to now remove the rod end caps and lower the crank slightly more (letting it rest on the remaining main bearing caps) to allow the seal to come out? Or will that invite disaster, or not work at all? I suppose the alternative is to remove the FMX trans, but frankly....I'd rather not.

Thanks for any advice.
Reply With Quote
  #11 (permalink)  
Old 06-13-2014, 10:10 AM
CC Member
Visit my Photo Gallery

 
Join Date: Jun 2014
Cobra Make, Engine:
Posts: 2
Not Ranked     
Default

Answer: Yes. You can, but it might not actually work.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 03:40 PM.


Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: CC Policy