Club Cobra Gas - N Exhaust  

Go Back   Club Cobra > Manufacturers, Engine Builders, tools, and parts. > Superformance

MMG Superformance
Nevada Classics
Main Menu
Module Jump:
Nevada Classics
Nevada Classics
MMG Superformance
MMG Superformance
Advertise at CC
Banner Ad Rates
Keith Craft Racing
MMG Superformance
March 2024
S M T W T F S
          1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
31            

Kirkham Motorsports

Like Tree1Likes
  • 1 Post By 8Ball

Reply
 
LinkBack Thread Tools Rate Thread Display Modes
  #1 (permalink)  
Old 10-09-2017, 12:59 PM
CC Member
Visit my Photo Gallery

 
Join Date: May 2015
Posts: 618
Neutral     
Default Cobra Valley Plastic Windshield Finally Installed

I've had this thing in my rafters for 6 months finally got up the nads to do with he swap...
Steps:
I elected to leave in the uprights which makes the whole thing easier.
Removed and carefully marked wings, side hooks,visors and rear view mirror. -actually looks cleaner without all of it...

1764 has the center rod, removed the two upward facing allens, (bracket to wind shield).
Remove two side screws and the whole thing comes up and forward away from the car, The little Allen screws are 4mm metric, removing is much easier if you shorten an Allen wrench by cutting the short end almost to the curve...these things are a ***** to restart...

To remove the glass two lower screws on either (bottom) side of the frame and the center support rod must be removed, then the frame bottom and sides top unit can be CAREFULLY Be pulled away.

If I had it to do again I would order a new rubber gasket...

I did not elect to glue the new one in, I cleaned out the frame and with the aid of a friend and dish soap worked the new one in. The center support rod made securing it together much easier...it is actually a frame compression device which hooks over the upper and lower frames together once assembled. The nuts are 5.5 mm (tiny)...

The glass install is a bit of an ordeal but the rest was pretty straightforward.

Last edited by tortuga; 10-09-2017 at 04:05 PM..
Reply With Quote
  #2 (permalink)  
Old 10-17-2017, 07:40 PM
CC Member
Visit my Photo Gallery

 
Join Date: May 2009
Location: Kingsholme, Qld
Cobra Make, Engine: Superformance Mark III, 347 Ford
Posts: 22
Not Ranked     
Default

Cool,
Can you tell us what is the vision like? (any distortion/halos/stars/colouring when looking through the curve into sun or headlights etc?)
Any flexing at speed?
Did you get to test the new screen for stability prior to fitting centre support?
Cheers
Steve
__________________
Either I am hard to get moving - or - once moving hard to stop. Hmmm, what the heck did Newton know anyway.
Reply With Quote
  #3 (permalink)  
Old 10-17-2017, 08:15 PM
CC Member
Visit my Photo Gallery

 
Join Date: May 2015
Posts: 618
Not Ranked     
Default

Beautiful noticeably clearer than the old glass,no distortion nothing a very nice piece.
Reply With Quote
  #4 (permalink)  
Old 10-18-2017, 01:58 AM
CC Member
Visit my Photo Gallery

 
Join Date: May 2009
Location: Kingsholme, Qld
Cobra Make, Engine: Superformance Mark III, 347 Ford
Posts: 22
Not Ranked     
Default

Cool.
Steve
__________________
Either I am hard to get moving - or - once moving hard to stop. Hmmm, what the heck did Newton know anyway.
Reply With Quote
  #5 (permalink)  
Old 09-08-2019, 09:47 AM
CC Member
Visit my Photo Gallery

 
Join Date: Jan 2011
Cobra Make, Engine:
Posts: 40
Not Ranked     
Default

With no glue or rubber gasket, how does the screen fit in the frame? Any issues?
Reply With Quote
  #6 (permalink)  
Old 05-26-2020, 08:30 AM
jstinson's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Mar 2020
Location: Ann Arbor, MI
Cobra Make, Engine: Superformance MK III, 396 Windsor
Posts: 14
Not Ranked     
Default

Question: Was this plastic wind screen polycarbonate? Acrylic? and now that its been in a while are you seeing any degradation in clarity? I would worry that these plastics will scratch easily due to their softness and can cloud over in time due to all the sand and dust that hits it.
Reply With Quote
  #7 (permalink)  
Old 05-26-2020, 10:57 AM
Karl Bebout's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Jun 2001
Location: Mesa, AZ
Cobra Make, Engine: ERA #2119 289FIA
Posts: 5,380
Not Ranked     
Default

I've had a Cobra Valley "polyglass" (polycarbonate) windshield on my car for about 2 years. I've put on at least 10K miles, and probably more. There is a minor bit of mini-pitting and one maybe 1/16" nick where a sizeable hunk of something hit. No doubt, a glass windshield would not have survived nearly as well. I live in Southern AZ and we have more dust and grit in the air than less arid areas. I also drove on a 5400 mile jaunt last summer with probably close to 1000 miles through the desert. The pitting has not caused any issues but is visible with oncoming headlights. Nothing bad, just noticeable. I don't have wipers but I do use anything handy to clean the windshield. Nothing special. I don't have any swirl marks as I would have had with softer plastics. I'm satisfied and can't imagine ever having to install another windshield My 2¢.
__________________
Karlos
"In the Land of the Pigs, The Butcher is King"
Reply With Quote
  #8 (permalink)  
Old 05-27-2020, 07:36 AM
8Ball's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Mar 2020
Location: Tellico Village, Tn
Cobra Make, Engine: Superformance
Posts: 25
Not Ranked     
Default

I've been running this same windshield for several years, love it, no issues what so ever.
By the way, RT strongly suggest gluing the windshield to the frame.
JohnnyRay likes this.
Reply With Quote
Reply

Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 12:07 PM.


Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: CC Policy
Links monetized by VigLink