Club Cobra - Streetbeast /Fiberfab/ CMC/ Innovative streetmachines

Main Menu

Portal
Forums

Nevada Classics

Advertise at CC

April 2024

S	M	T	W	T	F	S
	1	2	3	4	5	6
7	8	9	10	11	12	13
14	15	16	17	18	19	20
21	22	23	24	25	26	27
28	29	30

CC Advertisers

· Kirkham Motorsports
Superformance
· Finish Line
· Hurricane Motorsports
· Serpent Express
·
· Planet Cobra

· Shell Valley Classic Wheels
· Eight Stack Injection

Social Group Discussions in: Streetbeast /Fiberfab/ CMC/ Innovative streetmachines

Group Tools

Created Showing Discussions 81 to 90 of 195	Replies	Last Post
by DonB temp sensor locations on 302 I'm about to run wiring and I have an electric fan thermostat and temp gauge sensor. Instructions...	0	04-21-2016 02:02 PM by DonB
by ziggy75 e85 Has anyone tried running e85 with their Street Beast? I am interested in knowing if anyone has had...	16	04-21-2016 04:43 AM by mdross1
by Diversion Steering Column Hello all, I need to replace the original GM tilt column in my Beast (which I did not build). I...	5	04-07-2016 10:09 AM by ziggy75
by ziggy75 Grade 5 or Grade 8 bolts This may be a silly question but what fasteners should I be using to attach steering column support...	5	03-04-2016 06:21 PM by ziggy75
by TheExtreme CMC Fuel tank size. Trying to get the size of fuel tank. Can't measure due to shield. Were they standard on the CMC/SB?...	2	02-22-2016 08:48 AM by TheExtreme
by DonB nose shrouding Anyone shroud the inside of the nose to direct air through the radiator? What material did you use...	3	02-16-2016 03:39 AM by mdross1
by TheExtreme Wheels. Looking at new wheels. I used the wheel fitment tool and need 15x10 with 7" backspacing. Any ideas...	3	01-31-2016 08:53 AM by TheExtreme
by DonB roll bar openings, how'd you figure them? I decided to go ahead and raise my roll bar. I bought some dom tubing, cut off the old mounts and...	7	12-11-2015 02:13 PM by geeper
by ggrrbb StreetBeast Documents Hello ... I have recently purchased a lot of parts that appears to be mostly StreetBeast parts. ...	3	11-25-2015 02:57 AM by mdross1
by DonB finally, it's going to look better I took all the bare metal parts to the powder coater today. In about a week everything should look...	0	11-02-2015 08:00 PM by DonB

Page 9 of 20

Last »

All times are GMT -7. The time now is 03:57 PM.

Contact Us - Club Cobra Home - Archive - Top

The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: CC Policy

Links monetized by VigLink