Kirkham SALE!!! Scratch and Dent Clean Up Do It Yourself

[David Kirkham]

Originally Posted by fast_4

David, can you post a picture of the 427 SOHC billet valve covers?

Here they are.

The valve covers start out as a $360 billet of aluminum (I just asked Sandwich). They take 15 hours to machine each.

[David Kirkham]

UPDATE!!!

PRICE REDUCED!!!

Plastic fuel cell custom made for a 289 FIA car. The fuel cell was probably made by roto-molding. Never had fuel in it.

Retail $2000.
Today $900
$750

Inside foam will need to be replaced.

[David Kirkham]

UPDATE

I found a box of the original type sway bar mounts. They are made from aluminum.

We have:
1 set of 1"
3 sets of 7/8"
1 set of 3/4" (The size we normally use for our front sway bars).
1 side only of 1/2"
1 side only of 13/16"
1 side only "not drilled"

Retail: $75/set
$15 set
$10 set
I'll let the ones that only have 1 side go for $5 each.

[David Kirkham]

I found a few more. These have been in very high demand.

Turkey pan. This is our expensive, one piece turkey pan. Just like original.
Retail $400.
Today $200.

10 SOLD

[David Kirkham]

UPDATE!!!

While walking past this part I noticed one of the legs was welded back on in Poland. (The car was in a wreck). The control arm is NOT usable. It is garage art only.

This is an original right rear lower control arm for a 289 Cobra.
$250

[David Kirkham]

Originally Posted by David Kirkham

UPDATE!!!

While walking past this part I noticed one of the legs was welded back on in Poland. (The car was in a wreck). The control arm is NOT usable. It is garage art only.

This is an original right rear lower control arm for a 289 Cobra.
$250

Price reduced $200

[David Kirkham]

UPDATE
We have a few of these roll bars left. They have been quite popular.

This is a roll bar for a 427 car. It is made from 321 stainless. The tube is 1 1/2 OD with a 0.120 wall. Retail $750 Today $325

[David Kirkham]

I found a box of the original type sway bar mounts. They are made from aluminum.

We have:
1 set of 1"
3 sets of 7/8"
1 set of 3/4" (The size we normally use for our front sway bars).
1 side only of 1/2"
1 side only of 13/16"
1 side only "not drilled"

Retail $75 set.
Today $15 set.
$10 Set

[David Kirkham]

Turkey pan.

This is our expensive, one piece turkey pan. Just like original.

We have a few of these left.

Retail $400.
$200

[maxum_101]

Hey David

any chance you have a Canton oil pan....15-680S - 351W FRONT SUMP
I know its a long shot but I had to ask.

[David Kirkham]

Originally Posted by maxum_101

Hey David

any chance you have a Canton oil pan....15-680S - 351W FRONT SUMP
I know its a long shot but I had to ask.

Hmmmm,

Not sure. I have an entire container left to go through. I'll look.

David

[David Kirkham]

Guys,

The next parts I am going to post pictures of are no longer for sale. They sold today before I could even get them online.. However, I figured you all would like to see what we have been digging up. These are the exhaust manifolds for an AC 427 Cobra street car. They are extremely rare.

Notice the exhaust manifolds are NOT symmetrical. The right manifold is on top. The left manifold is on bottom.


Notice the heat riser port on the left manifold to run the choke on the dual quad carbs.


Casting numbers for the left manifold.


Other side of the left manifold.


Right manifold. I have no idea why the casting numbers are the same.


Right manifold


Right manifold and left manifold together. Right is on top.


Right manifold and left manifold together. Right is on top.

[David Kirkham]

These are 9 bin organizers. The tilt out drawers are about 2 inches x 2 inches.

I think we paid $10 each for them in a big quantity buy. I'll let these go for $5 each. We probably have 20 of them. New, in the wrapper.



As you can see in the below photo, we use them to organize lots of nuts and bolts and little parts. These bins (and the parts inside them aren't part of the sale )

[David Kirkham]

We have 5 of these Nisonger reproduction Smiths Tachs. They retail at $100 each??? Not sure, someone correct me if I'm wrong. I'll let these go for $50 each. New, in the box.

4 SOLD

[David Kirkham]

I found a box of the original type sway bar mounts. They are made from aluminum.

We have:
1 set of 1"
3 sets of 7/8"
1 set of 3/4" (The size we normally use for our front sway bars).
1 side only of 1/2"
1 side only of 13/16"
1 side only "not drilled"

These for $75/set. I'll let the sets go for $15. I'll let the ones that only have 1 side go for $5 each.

[David Kirkham]

These came off a 289 Comp car. Now, that doesn't mean they are "original." Those cars had a hard life and exhaust was expendable. The Snap Lock (Nice product Jorgen) floor tiles are 1 foot squares.

These are used and abused. Dented and scratched.

$50 owns them. Shipping will be $50.

SOLD

[David Kirkham]

SOLD

This is a Mark Williams MAGNESIUM housing for a Ford 9 inch. This was part of our project when we went to Snezhinsk, Russia to work with nuclear weapons engineers on a nuclear non-proliferation project. I think we paid $500 for the case. Let me know if someone finds a link. Make a reasonable offer. Brand new.

[David Kirkham]

We filled up the UPS truck today.

[LMH]

Originally Posted by David Kirkham

We filled up the UPS truck today.

Ok, he is NOT smiling!
Larry

[cdnus]

Yeah sure---tease us all by slipping that beautiful copper cobra in the background.

[/quote]