SUPPORT OUR SPONSOR

Go Back   Club Cobra > Club Cobra Tech Areas > Shop Talk

Welcome to Club Cobra!  The World's largest non biased Shelby Cobra related site!

  •  » Representation from nearly all Cobra/Daytona/GT40 manufacturers
  •  » Help from all over the world for your questions
  •  » Build logs for you and all members
  •  » Blogs
  •  » Image Gallery
  •  » Many thousands of members and nearly 1 million posts! 

YES! I want to register an account for free right now!  p.s.: For registered members this ad will NOT show

MMG Superformance
Nevada Classics
MMG Superformance
Main Menu
Nevada Classics
Nevada Classics
Keith Craft Racing
Keith Craft Racing
Advertise at CC
Banner Ad Rates
MMG Superformance
MMG Superformance
MMG Superformance
March 2024
S M T W T F S
          1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
31            
  #1 (permalink)  
Old 05-21-2003, 02:28 PM
Curt C.'s Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Nov 1999
Location: Las Vegas, NV
Cobra Make, Engine: Classic Roadster; 351W
Posts: 743
Not Ranked     
Default Electrical gurus; help me rig a neutral safety switch

I have a Wilwood clutch/mc pedal assembly routed to a Tilton Hyrdraulic TO. Car is a Classic Roadster and probably has the wiring set up to do it - I will check. How can I rig a mechanism to trigger. Thanks
Reply With Quote
  #2 (permalink)  
Old 05-21-2003, 02:54 PM
Mr.Fixit's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Mar 2002
Location: so cal, Cal
Cobra Make, Engine: I used to fix them for a living
Posts: 2,563
Not Ranked     
Default

The tremec has a neutral safety switch built in. Use it as a trigger to control an interrupt relay on the start circuit of the ign key.
__________________
In a fit of 16 year old genius, I looked down through the carb while cranking it to see if fuel was flowing, and it was. Flowing straight up in a vapor cloud, around my head, on fire.
Reply With Quote
  #3 (permalink)  
Old 05-21-2003, 04:35 PM
Curt C.'s Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Nov 1999
Location: Las Vegas, NV
Cobra Make, Engine: Classic Roadster; 351W
Posts: 743
Not Ranked     
Default

Mr. Fixit, thanks for the response. However, it went way over my head. Speak to me like I am an electrical Idiot please. I dont know where to begin "interrupt relay"?? So the tranny has to be in Neutral or the starter wont work? I have the Tremec manual. Are there instructions in there?
Reply With Quote
  #4 (permalink)  
Old 05-21-2003, 05:26 PM
xlr8or's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Dec 2001
Location: San Diego, CA
Cobra Make, Engine:
Posts: 2,977
Not Ranked     
Default

Basically he means to use the built in switch on the tranny and you use it to interupt the wire on your ignition switch that engages the starter. You want to use a relay so it protects the ignition circuit.

I'm sure someone around here probably has a wiring diagram for that.

Scott
__________________
Remember, It's never too early to start beefing up your obituary.
Reply With Quote
  #5 (permalink)  
Old 05-22-2003, 04:53 AM
trularin's Avatar
Member of the north
Visit my Photo Gallery

 
Join Date: May 2003
Cobra Make, Engine: A Cobra
Posts: 11,207
Not Ranked     
Default

There is a wire to either the starter, or starter solinoid. You will want to interrupt that wire and have it go to a relay controlled by the transmission and then to the starter/solinoid ( no taking off for spelling ).

When the transmission is in neutral, the relay closes and allows current to flow to the starter/solinoid. If the trans is in any other position, the relay will not close and the starter can not be engaged.

You want to use a relay for two big reasons; service and protection.

Hope this helps.

Trularin
__________________
I'm a writer, feed the artist and buy a book.
Reply With Quote
  #6 (permalink)  
Old 05-22-2003, 05:43 AM
CC Member
Visit my Photo Gallery

 
Join Date: May 2002
Location: Brisbane Australia, QLD
Cobra Make, Engine: RMC under re-construction, GenIV with tremec 600, Jag 3.31 L/S diff
Posts: 3,318
Not Ranked     
Default

Curt..Bet ya still confused...
See if I can make it easier.
On the back of your ignition switch you will find a number of wires..find the one that goes to the S (start) terminal on your starter solenoid. It will be a heavy (12Gauge maybe) wire.

This wire needs to be disconnected from the S (start) terminal on the solenoid and connected to the neutral switch on your Trans. From the other terminal of the neutral switch on the trans, connect a wire (same size as the before mentioned wire) and route this wire and connect to the same terminal ( the start (S) terminal) on the starter solenoid, from where you removed the original wire.

What happens is this: If you are in neutral, the switch on the trans allows power to be passed to the starter..thereby starting the engine. If you're in gear, it wont allow power thru, thereby preventing the engine from starting whilst in a gear and running over ya dog.

When the fellas talk about a relay or a solenoid...they are referring to an electrical switch which is activated by power (as opposed to a switch you manually turn on). Relays and solenoids are used to switch large current draw components(starters, horns, fans etc), which use a current which would fry a normal switch. There is of course a manual switch which activates the solenoid/relay (ignition for example) but only needs to conduct relatively low power to switch the solenoid/relay which in turn switches the heavy draw component.

Whew!.....hope that helped

Les
__________________
It's impossible to soar like an eagle when you're surrounded by turkeys.
Reply With Quote
  #7 (permalink)  
Old 05-22-2003, 06:50 AM
Senior Club Cobra Member
Visit my Photo Gallery

 
Join Date: Jul 2000
Location: Las Vegas, NV
Cobra Make, Engine: ERA 427 SO
Posts: 1,126
Not Ranked     
Default

Curt, hope this upload works...see the attached photo for a very crude wiring diagram.
The easiest way would be to take the wire that now energizes the starter solenoid off the solenoid, hook it up to a power and a trigger terminal on the solenoid, run a wire from the other power terminal back to the solenoid and run a wire from the other trigger terminal to the trans neutral switch. If it is a 2-wire switch at the trans, run the other terminal to a ground.
It works like this: When you switch to the start position, power from the switch goes through the relay trigger circuit, to the trans switch and (if the trans is in neutral) to ground, energizing the trigger and closing the relay. At that point, power goes through the power circuit on the relay and on to the starter solenoid and cranks the engine. If the trans is not in neutral, the trigger circuit is never energized and power never gets to the solenoid...
Attached Images
 
__________________
Ken
Reply With Quote
  #8 (permalink)  
Old 05-22-2003, 08:22 AM
Curt C.'s Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Nov 1999
Location: Las Vegas, NV
Cobra Make, Engine: Classic Roadster; 351W
Posts: 743
Not Ranked     
Default

Perfect, the explanations and diagram are exactly what I needed. One last question. What kind of relay (description) and where can I find it? Hehe, this is much simpler than I previously thought.
Reply With Quote
  #9 (permalink)  
Old 05-22-2003, 08:37 AM
Senior Club Cobra Member
Visit my Photo Gallery

 
Join Date: Jul 2000
Location: Las Vegas, NV
Cobra Make, Engine: ERA 427 SO
Posts: 1,126
Not Ranked     
Default

Radio Shack has an inexpensive one, all black plastic housing (a little chintzy), but it is rated @ 30 amps, should be sufficient. It has a mini-diagram on the package and on the body of the relay. Just make sure you get one designed and rated for 12 volts.
__________________
Ken
Reply With Quote
  #10 (permalink)  
Old 05-22-2003, 06:50 PM
Curt C.'s Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Nov 1999
Location: Las Vegas, NV
Cobra Make, Engine: Classic Roadster; 351W
Posts: 743
Not Ranked     
Default

OK I got the switch Mr0077 described. It has four posts: 12V in; 12V out; 12V switch on/off; and a ground. Let's see what I have learned: The wire from the solenoid previously going to the starter goes to 12V in; 12V out goes to the starter; 12V switch on/off goes to the tranny switch and ground goes to ground. Is this correct? Also, I still have to ground the other side of the tranny switch?? Per the diagram on the relay package, the 12V in crosses the 12V switch on/off. The break (relay?) occurs after this intersection going to 12V out. You know, I have assembled 2 engines starting with short blocks, tuned carbs, set up blown EFI combos, but I am simply ignorant on electrical. They don't teach this important stuff in B. School or the car mags for that matter. I do enjoy learning and self teaching though. Thanks guys.

Last edited by Curt C.; 05-22-2003 at 06:52 PM..
Reply With Quote
  #11 (permalink)  
Old 05-22-2003, 08:06 PM
Senior Club Cobra Member
Visit my Photo Gallery

 
Join Date: Jul 2000
Location: Las Vegas, NV
Cobra Make, Engine: ERA 427 SO
Posts: 1,126
Not Ranked     
Default

Curt, your description was right, except where you hook up the transmission. Refer to the photo, and you'll see that the same 12V going to the contact terminal should also go to the trigger terminal (more on that in a second). The other side of the trigger terminal goes to the transmission. If it is a one-wire trans switch it grounds internally...if it is a 2-wire trans switch, the second wire should be grounded to the frame, trans case, etc. With this wiring layout, you use the starter wire to energize the relay.
An alternate way to wire the relay is to have a 12V (FUSED!) wire going to the 12V "in" terminal and the ignition starter wire going straight to a trigger terminal, so all the starter voltage would do is trigger the relay, and the 12V in would energize the starter. The 12V out still would go to the starter solenoid terminal and the other trigger terminal would still go to the transmission...did that make any sense at all?
And also, I am assuming that what they call 12V in and out are shown as passing through the contacts on their diagram (theirs should be similar to mine in the photo). Good luck!
__________________
Ken
Reply With Quote
  #12 (permalink)  
Old 05-23-2003, 10:26 AM
Curt C.'s Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Nov 1999
Location: Las Vegas, NV
Cobra Make, Engine: Classic Roadster; 351W
Posts: 743
Not Ranked     
Default

Yes, Yes, I see. I somehow got it in my head that there were 3 terminal in your drawing. Yes, the diagram on the package is just like yours except the lines are perpendicular. I thought something was wrong with my description because it contained two grounds. One last question. The existing wire running from the SN to the starter is quite large, approx 1/8 inch. Will 12 GA be enough to energize the starter or should I go larger?
Reply With Quote
  #13 (permalink)  
Old 05-23-2003, 11:11 AM
Senior Club Cobra Member
Visit my Photo Gallery

 
Join Date: Jul 2000
Location: Las Vegas, NV
Cobra Make, Engine: ERA 427 SO
Posts: 1,126
Not Ranked     
Default

Curt, I guess I got a little myopic and didn't ask...does your starter have a solenoid mounted on it? Do you have a firewall mounted solenoid? If you have either one, does the 1/8" wire you're talking about (from the SN) run from the ignition switch to the solenoid, or from a firewall-mounted solenoid to the starter? If from the ignition switch, the relay and 12 GA wire should work; if that big wire comes from a solenoid or somewhere else, you will want to insert the new relay in line with thestarter wire that runs from the ignition switch to the solenoid (or relay)...that should be a smaller wire, maybe 12 GA or so. That size wire (1/8") makes me think it is coming from a solenoid, not the ignition switch (usually switch wiring is smaller, 12 Ga or so).
__________________
Ken
Reply With Quote
  #14 (permalink)  
Old 05-23-2003, 02:41 PM
Curt C.'s Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Nov 1999
Location: Las Vegas, NV
Cobra Make, Engine: Classic Roadster; 351W
Posts: 743
Not Ranked     
Default

Yup, its coming directly from the firewall mounted SN (solenoid) to the starter. I will look for a wire going to the SN from the ignition and report back.

Curt
Reply With Quote
  #15 (permalink)  
Old 05-23-2003, 03:29 PM
SCOBRAC's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Jan 2002
Location: Northern California, CA
Cobra Make, Engine: -Sold- Contemporary 427S/C # CCX-3152 1966 427 Med Rise Side Oiler, 8v 3.54:1 Salisbury IRS, Koni's.. (Now I'm riding Harleys)
Posts: 2,567
Not Ranked     
Default

Nuetral? as in? www.switzerland.com
__________________
michael

A man that is young in years, may be old in hours, if he have lost no time. But that happeneth rarely. Generally, youth is like the first cogitations, not so wise as the second. For there is a youth in thoughts, as well as in ages... Sir Francis Bacon (1561-1626)
Reply With Quote
  #16 (permalink)  
Old 05-23-2003, 03:37 PM
Senior Club Cobra Member
Visit my Photo Gallery

 
Join Date: Jul 2000
Location: Las Vegas, NV
Cobra Make, Engine: ERA 427 SO
Posts: 1,126
Not Ranked     
Default

SCOBRA, good one! Yeah, I guess we need a neutral switch...that is, a switch that lets the neutral countries to see things our way...hahahahahaha...thread entropy.
__________________
Ken
Reply With Quote
  #17 (permalink)  
Old 05-23-2003, 04:27 PM
CC Member
Visit my Photo Gallery

 
Join Date: Jun 2001
Location: Washington DC Metro (Virginia), VA
Cobra Make, Engine: Classic Roadsters, Tweaked 351W, T-5Z, CRII Tech Support Team.
Posts: 1,895
Not Ranked     
Default

Not sure it needs to be this complicated. On a CR, wire #121 runs from the ignition start to the starter safety switch on the trans. Wire #126 runs from the trans neutral safety switch to the starter solenoid.

Plug the trans wiring harness into the trans neutral safety switch and backup light switch, and you're done.

That being said, CR also had to accommodate those using automatic trans's. You may have to locate the AT 121 - 126 connection and jumper it.
Reply With Quote
  #18 (permalink)  
Old 05-23-2003, 07:25 PM
Double Venom's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Nov 1999
Location: Pentwater, Mi
Cobra Make, Engine: Professional Cobra & Streetrod Builder
Posts: 5,352
Send a message via AIM to Double Venom
Not Ranked     
Default

WOW!
I had no idea this was about a CR's harness and a neutral switch!
Like Jack says, IT'S ALREADY IN THERE!

Find the small grey plug plug coming off the steering column harness with only two wires - 126/121. Extend these wires to the neutral safety switch on the transmission and your done!

Don't know which plug on the transmission is the neutral safety switch? Buy a cheap dwell meter with an audible tone for continuity. Touch the probes to the two brass pins on the tranny, with the tranny in neutral. Nothing should happen, put the tranny in gear and you will hear the tone.

That simple

DV...Plug it in and bring that baby to the Fling!

Last edited by Double Venom; 05-23-2003 at 07:29 PM..
Reply With Quote
  #19 (permalink)  
Old 05-24-2003, 07:52 AM
dscott's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: May 2000
Location: Sauk Centre, MN
Cobra Make, Engine: Owner, Classic Roadsters II
Posts: 1,347
Not Ranked     
Default

The same wires come off the engine harness under the hood. There is a 4 wire plug with wires 121, 126, and the other 2 are for the backup lights. Classic should have supplied an extension for these wires that reach the trans. Somewhere along the line someone must have put a jumper on wire 121 and 126 otherwise the car would not start.
Don
Reply With Quote
  #20 (permalink)  
Old 05-24-2003, 12:15 PM
Curt C.'s Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Nov 1999
Location: Las Vegas, NV
Cobra Make, Engine: Classic Roadster; 351W
Posts: 743
Not Ranked     
Default

You guys saw me coming. This morning I got out the CR manual in an attempt to verify the starter wire. There they were 121 & 126 starter power and starter control. Don has to be right. Somewhere in the system 126 and 121 are combined right? Anyone familliar with the Tremec. There are two electrical connectors: one in the rear with a pigtail coming off it and one in the middle of the trans with male connectors. Which is the neutral safety switch? My Tremec manual does not identify either.
Reply With Quote
Reply


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 11:42 PM.


Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: CC Policy