Keith Craft Inc.- We service what we sell!!! Check out our Cobra engines!!! We build high performance racing engines and components for the fast pace strip racing industry as well as daily drivers who want to be FIRST!!!

FE Forums sponsored by Keith Craft Inc.


Go Back   Club Cobra > Engine Building, Tuning, and Induction > FE TALK

Welcome to Club Cobra!  The World's largest non biased Shelby Cobra related site!

  •  » Representation from nearly all Cobra/Daytona/GT40 manufacturers
  •  » Help from all over the world for your questions
  •  » Build logs for you and all members
  •  » Blogs
  •  » Image Gallery
  •  » Many thousands of members and nearly 1 million posts! 

YES! I want to register an account for free right now!  p.s.: For registered members this ad will NOT show

Nevada Classics
MMG Superformance
Main Menu
Nevada Classics
Nevada Classics
MMG Superformance
MMG Superformance
Advertise at CC
Banner Ad Rates
Keith Craft Racing
MMG Superformance
MMG Superformance
Keith Craft Racing
March 2024
S M T W T F S
          1 2
3 4 5 6 7 8 9
10 11 12 13 14 15 16
17 18 19 20 21 22 23
24 25 26 27 28 29 30
31            

Kirkham Motorsports

Like Tree12Likes

Reply
 
LinkBack Thread Tools Rate Thread Display Modes
  #101 (permalink)  
Old 12-04-2017, 10:36 AM
CC Member
Visit my Photo Gallery

 
Join Date: May 2012
Location: Wickenburg, AZ
Cobra Make, Engine: Superformance, 427 FE
Posts: 197
Not Ranked     
Default

I did want to comment on those who said these aluminum blocks need a lot of work (cost/time) to get them right and that is one of the reasons they did not like doing them.
I see their point. The Pond block did require a lot of attention and multiple check for fit steps. This equates to time and that means money.
So for those who think it is just bolting on new parts, that is not how it goes.

I am thankful my machinist took the time and attention to detail. I could not imagine building such a thing with out, pressure testing, heat cycling, test fitting, dyno runs and other checks that are to numerous to mention. All I can say, is the block took a lot of machining.

I feel good with my decision, I did not pick aluminum block for bling or bragging rights, I did it because I did wanted all new components. Thanks to this forum and heading warnings of those who have gone before gave me things to watch for, I know it wasn't just thrown together.

It is awaiting install into the car and only putting on miles to see if all is well.
__________________
If enough people disagree with me, I know I am doing it right
Reply With Quote
  #102 (permalink)  
Old 12-05-2017, 05:49 AM
moore_rb's Avatar
CC Member
Visit my Photo Gallery

 
Join Date: Aug 2015
Cobra Make, Engine: All original, with Chevy engine since 1964
Posts: 996
Not Ranked     
Default

Quote:
Originally Posted by FUNFER2 View Post
Brent, I've heard that FE's are harder to select a proper cam, without giving your secret's, please explain that situation and what is best to get it right.
Quote:
Originally Posted by blykins View Post
No thanks.
Quote:
Originally Posted by cycleguy55 View Post
Interpretation / conclusion: Brent has grown tired of FUNFER2's endless questions (with no apparent end in sight) under the guise of 'research'.
.
Quote:
Originally Posted by rodneym View Post
While I'm sure Brent is (or can be) tired of tire kickers, my take away was that he didn't want to invite all the online "experts" who might have something to say about his expertise.

Answering that question could be begging for attention from the peanut gallery.

The operation of an internal combustion engine is 100% science (the laws of physics regulate everything that takes place inside there)....

However- Building engines (especially high performance engines) requires the skill of a studied and experienced artist, not a lab-coat wearing Poindexter-

If you were to spend $500 in a luxury restaurant, eating the finest gourmet meal you have ever tasted, it would show extremely poor taste too:

1) Ask the chef for his recipes.
2) Assume that your could EVER take those recipes home, and re-create that same meal all over again.

There is a matter of etiquette at play in both the novice's original question, and the master's well-reasoned response... I get where Brent is coming from
__________________
- Robert
Reply With Quote
  #103 (permalink)  
Old 12-05-2017, 08:27 AM
CC Member
Visit my Photo Gallery

 
Join Date: May 2012
Location: Wickenburg, AZ
Cobra Make, Engine: Superformance, 427 FE
Posts: 197
Not Ranked     
Default

Brent talks with experience that is for sure. He stated that extra work takes extra time/ money. I was willing to pay to get it right. I took all his warnings to heart and it gave us things to watch for. Therefore I did not have surprises and was willing to pay/spend the time to check and recheck.

Brent and my Bud (my builder) had more than one conversation as did I with him. Some parts were obtained from him as well. I thank them both.

So I am saying, that his warnings are well founded and if a customer expected a firm price to build such a motor, the builder could take it in the shorts. I could see where someone going in blind could think the reputable builder is taking advantage of him by upping the price, due to more work needing done to a new part.

Now it still has to run 100,000 trouble free, fire breathing miles for all to pay off !!!!!
__________________
If enough people disagree with me, I know I am doing it right
Reply With Quote
  #104 (permalink)  
Old 01-16-2018, 02:03 PM
CC Member
Visit my Photo Gallery

 
Join Date: May 2012
Location: Wickenburg, AZ
Cobra Make, Engine: Superformance, 427 FE
Posts: 197
Not Ranked     
Default

I just wanted to do an update. Yesterday was the first drive with the new engine. I am taking it easy during break-in. Obviously power was there. I think I have some carburetor work to do because there is a hesitation.
Idle is choppy but no problem with the power brakes. I did the 5 speed with 0.64 5th and it cruises nicely at 65 - 75 mph / 1900 - 2100 rpm, and will still accelerate smartly
__________________
If enough people disagree with me, I know I am doing it right
Reply With Quote
Reply


Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On



All times are GMT -7. The time now is 06:26 PM.


Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: CC Policy