Club Cobra

Club Cobra (http://www.clubcobra.com/forums/)
-   Scratch Builders Forum (http://www.clubcobra.com/forums/scratch-builders-forum/)
-   -   289 progress........ (http://www.clubcobra.com/forums/scratch-builders-forum/102466-289-progress.html)

LightNFast 08-11-2011 07:22 PM

.....................

1985 CCX 08-12-2011 06:35 AM

Well the BBQ will be without the lil 289, the motor will be there LOLOL

I think next ally part will be boot then hood. Flares will be last as I will be making those.

Thanks for the props guy's............

1985 CCX 09-12-2011 05:41 AM

Plumbing has started....................

http://img823.imageshack.us/img823/6...1109120728.jpg

*13* 09-12-2011 06:58 AM

Looking good! I'm about 3 hours from you now, livin' in VT. We'll have to get together at some point. I'd love to see the car in person!

1985 CCX 09-12-2011 12:34 PM

And I yours............
Planning a cruise to SAAC37 this year, maybe you are up for the event with the NH guys.... :D

*13* 09-12-2011 04:25 PM

Just got my Webers dialed in & popped another head gasket. I need to pull my motor & have it gone through. Don't know when it'll be on the road again, but I know we're up for some East Coast sight seeing.

PDUB 09-13-2011 12:31 AM

It's getting crowded up in that neck of the woods;)! Quite the switch there Hyde... sent a PM.

Looking good Jeff. I'm looking forward to seeing it in person, as well.

1985 CCX 12-29-2011 05:58 PM

Guess its time to get back on this huh?
Life..............
Family..............
Work....................

2012 is the year!

http://img838.imageshack.us/img838/7...heelcenter.jpg

D&M2 12-29-2011 06:48 PM

I hear ya. The basement is almost finished so I should be able to spend some time on mine as well.

Mike

LMH 12-29-2011 07:26 PM

Yep, same here! This IS the year Jeff!
Larry

1985 CCX 12-30-2011 03:03 PM

2012 it is then! Hope everyone is able to get rolling down the road once again. Miss the driving fun.;)

1985 CCX 01-04-2012 05:05 PM

Off to Panel Craft for ally rear flares with rolled edge, ally boot and ally hood skin attachement to frames...... The additiion of the aluminum to the glass shell is working out nicely. After the body was attached to the frame it is one solid car! The doors are super solid and close with confidence!



http://img546.imageshack.us/img546/5...lcraft1041.jpg

Future color of this car! http://img214.imageshack.us/img214/5...colorofcar.jpg

*13* 01-04-2012 05:13 PM

Yup, she'd starting to take on that look! The one that says "are you feeling lucky?"

1985 CCX 01-04-2012 05:17 PM

Ok, very excited about the battery box as it is so correct. Right down to the heat shield, did not want me to post until insulated and painted but it is awesome and fits like a glove.

http://img829.imageshack.us/img829/2...tterytrayc.jpg

http://img855.imageshack.us/img855/1...tterytrayb.jpg

http://img820.imageshack.us/img820/1...tterytraya.jpg

Top notch quality and top notch accuracy....

1985 CCX 01-04-2012 05:38 PM

5 bolt Bellhousing ready for installation. Once the car returns, motor and trans drop.....

http://img546.imageshack.us/img546/6...ellhousing.jpg

LMH 01-04-2012 06:16 PM

That's great! I didn't know Nick made a battery box. Adding that to my list!
Larry

*13* 01-04-2012 06:26 PM

Hey, I have one of those! Still needs to be installed ...

MAStuart 01-04-2012 08:11 PM

Jeff it is looking good. Question about your bellhousing..Is it for a large or small flywheel and is it aluminum or iron. I have been working on my coupe and it will be no fun to get the engine and trans in and out. I think I will have to install the engine first and then the trans from the inside. Something else is the engine on your car centered in the frame or offset. On the coupe the engine is lowered 1 inch and offset 1 inch to the passenger side. Do you have the driveshaft yet. Is so how long is it . center to center of ujoint. They appear to be verry short.....6 to 8 inches. I kind of think I should have built a car similar to yours. I might have a hard time getting in and out of a coupe. Mark

mickmate 01-04-2012 08:33 PM

Hi Mark, his drivetrain is like 427 offset 1/2" to right. Lesher with the old CCX/Upstate Coupe narrowed the frame at the rear to sit beside it and get some headroom.
Welcome to Lesher Motorsports

MAStuart 01-04-2012 08:50 PM

Nick are you saying that 289 leaf spring cars have the engine offset 1/2 to the right? Mark


All times are GMT -7. The time now is 08:52 AM.

Powered by vBulletin® Version 3.8.0
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Friendly URLs by vBSEO 3.6.0
The representations expressed are the representations and opinions of the clubcobra.com forum members and do not necessarily reflect the opinions and viewpoints of the site owners, moderators, Shelby American, any other replica manufacturer, Ford Motor Company. This website has been planned and developed by clubcobra.com and its forum members and should not be construed as being endorsed by Ford Motor Company, or Shelby American or any other manufacturer unless expressly noted by that entity. "Cobra" and the Cobra logo are registered trademarks for Ford Motor Co., Inc. clubcobra.com forum members agree not to post any copyrighted material unless the copyrighted material is owned by you. Although we do not and cannot review the messages posted and are not responsible for the content of any of these messages, we reserve the right to delete any message for any reason whatsoever. You remain solely responsible for the content of your messages, and you agree to indemnify and hold us harmless with respect to any claim based upon transmission of your message(s). Thank you for visiting clubcobra.com. For full policy documentation refer to the following link: